Weider Cjxt3 Master Trainer User Manual - Page 5

completed.

Get Weider Cjxt3 Master Trainer PDF manuals and user guides View all Weider Cjxt3 Master Trainer manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

3. Press the 1 1/4" Inner Cap (57) into the Front 3 Upright (42). Attach the 1" Plastic Stop (64) to the center hole in the Stop Bracket (63) with a 5/16" x 1 1/2" Bolt (24) and 5/16" Nylon Locknut (3). Attach the Stop Bracket (63) to the Front Upright (42) with a 5/16" x 2" Bolt (61), a 5/16" Flat Washer (8) and a 5/16" Nylon Locknut (3). Slide the Front Upright (42) onto the two 5/16" x 2 1/2" Carriage Bolts (1) in the Base (4). Attach the Front Upright to the Base with two 5/16" Nylon Locknuts (3). Do not tighten the Nylon Locknuts yet. 63 Single Hole 3 3 24 57 6 42 4 3 4. Press two 2" Inner Caps (27) into the Top Frame (67). Attach the Top Frame (67) to the Front Upright (42) with two 5/16" x 2 3/4" Bolts (11). 5/16" Flat Washers (8) and 5/16" Nylon Locknuts (3). Do not tighten the Nylon Locknuts yet. Attach the Top Frame (67) to the Stop Bracket (63) with a 5/16" x 2 3/4" Bolt (11), 5/16" Rat Washer (8) and 5/16" Nylon Locknut (3). Do not tighten the Nylon Locknut yet. Attach the Top Frame (67) to the Rear Upright (82) with two 5/16" x 2 3/4" Bolts (11), 5/16" Flat Washers (8) and 5/16" Nylon Locknuts (3). lighten all Nuts used in steps 2 through 4. 5. Set the two Weight Bumpers (19) on the indicated plate on the Base (4). Align the holes in the Weight Bumpers with the holes in the plate. Stack nine Weights (25) on the Weight Bumpers (19). Each Weight must be turned so the "welder" logo is on top, and the pin groove is facing the Front Upright (42). The holes In the Weights must be aligned with the holes in the Weight Bumpers. CAUTION: Be careful to avoid Upping the stack of Weights until step 6 Is completed. A 11 8 27 3 82 5 11 11 8 67 3 27 3 63 42 25 0 `Weider" Logo on Top Pin Groove 9 42 19 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
3.
Press
the
1
1/4"
Inner
Cap
(57)
into
the
Front
Upright
(42).
Attach
the
1"
Plastic
Stop
(64)
to
the
center
hole
in
the
Stop
Bracket
(63)
with
a
5/16"
x
1
1/2"
Bolt
(24)
and
5/16"
Nylon
Locknut
(3).
Attach
the
Stop
Bracket
(63)
to
the
Front
Upright
(42)
with
a
5/16"
x
2"
Bolt
(61),
a
5/16"
Flat
Washer
(8)
and
a
5/16"
Nylon
Locknut
(3).
Slide
the
Front
Upright
(42)
onto
the
two
5/16"
x
2
1/2"
Carriage
Bolts
(1)
in
the
Base
(4).
Attach
the
Front
Upright
to
the
Base
with
two
5/16"
Nylon
Locknuts
(3).
Do
not
tighten
the
Nylon
Locknuts
yet.
4.
Press
two
2"
Inner
Caps
(27)
into
the
Top
Frame
(67).
Attach
the
Top
Frame
(67)
to
the
Front
Upright
(42)
with
two
5/16"
x
2
3/4"
Bolts
(11).
5/16"
Flat
Washers
(8)
and
5/16"
Nylon
Locknuts
(3).
Do
not
tighten
the
Nylon
Locknuts
yet.
Attach
the
Top
Frame
(67)
to
the
Stop
Bracket
(63)
with
a
5/16"
x
2
3/4"
Bolt
(11),
5/16"
Rat
Washer
(8)
and
5/16"
Nylon
Locknut
(3).
Do
not
tighten
the
Nylon
Locknut
yet.
Attach
the
Top
Frame
(67)
to
the
Rear
Upright
(82)
with
two
5/16"
x
2
3/4"
Bolts
(11),
5/16"
Flat
Washers
(8)
and
5/16"
Nylon
Locknuts
(3).
lighten
all
Nuts
used
in
steps
2
through
4.
5.
Set
the
two
Weight
Bumpers
(19)
on
the
indicated
plate
on
the
Base
(4).
Align
the
holes
in
the
Weight
Bumpers
with
the
holes
in
the
plate.
Stack
nine
Weights
(25)
on
the
Weight
Bumpers
(19).
Each
Weight
must
be
turned
so
the
"welder"
logo
is
on
top,
and
the
pin
groove
is
facing
the
Front
Upright
(42).
The
holes
In
the
Weights
must
be
aligned
with
the
holes
in
the
Weight
Bumpers.
CAUTION:
Be
careful
to
avoid
Upping
the
stack
of
Weights
until
step
6
Is
completed.
3
63
Single
Hole
3
3
24
57
6
42
4
3
A
27
3
82
11
8
42
3
11
8
11
67
3
63
27
5
25
0
9
`Weider"
Logo
on
Top
Pin
Groove
42
19
4