Weider Flex 8960 Uk Manual - Page 9

Set the Seat Carriage 12 on the Bench Frame

Page 9 highlights

12. Lubricate two Small Wheels (47) with grease. Slide a Steel Tube (57) into a 32mm Spacer (46). Orient the Wheels as shown in the inset drawing, and slide them onto the ends of the Steel Tube. Attach the wheel assembly to the indicated set of holes in the Seat Carriage (12) with an M8 x 84mm Bolt (60) and an M8 Nylon Locknut (65). Do not overtighten the Locknut; the Small Wheels (47) must pivot freely. Repeat with another wheel assembly and an M8 x 82mm Bolt (95). Orient the Seat (13) and the Seat Carriage (12) as shown. Attach the Seat to the Seat Carriage with four M6 x 16mm Screws (82). 13. Lubricate two Small Wheels (47) with grease. Slide a Steel Tube (57) into a 32mm Spacer (46). Orient the Wheels as shown in the inset drawing, and slide them onto the ends of the Steel Tube. Set the Seat Carriage (12) on the Bench Frame (5). Have one person press the Seat (13) against the Bench Frame. Press the wheel assembly tight against the bottom of the Bench Frame and attach it to the lowest set of holes in the Seat Carriage with an M8 x 84mm Bolt (60) and an M8 Nylon Locknut (65). Do not overtighten the Locknut; the Small Wheels (47) must pivot freely. Slide the Seat Pin (45) through the Seat Carriage (12) and an adjustment hole in the Bench Frame (5). 14. Press two 25mm Square Inner Caps (54) into the indicated ends of the Backrest Frame (15). Press the Backrest Cap (16) onto the other end of the Backrest Frame. Attach a Plastic Foot (53) to the Backrest Frame with an M4 Washer (92), and an M4 x 25mm Screw (56). Attach a Guard Plate (17) to the inside of the Backrest Frame (15) with two M4 x 10mm Screws (96). Attach the other Guard Plate in the same manner. 12 13 Wheel Assembly 65 95 60 Small Side 57 46 47 47 Large Side 12 82 65 Wheel 82 Assembly 13 13 60 45 65 12 5 Adjustment Hole Small Side 57 46 47 47 46 47 57 47 Large Side 14 15 16 92 53 56 17 96 54 17 15 14 15. Orient the Backrest (14) as shown. Attach the Backrest to the Backrest Frame (15) with four M6 x 38mm Screws (58) and four M6 Washers (77). 15 77 58 77 58 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26

9
12. Lubricate two Small Wheels (47) with grease. Slide
a Steel Tube (57) into a 32mm Spacer (46). Orient
the Wheels as shown in the inset drawing, and
slide them onto the ends of the Steel Tube.
Attach the wheel assembly to the indicated set of
holes in the Seat Carriage (12) with an M8 x
84mm Bolt (60) and an M8 Nylon Locknut (65).
Do
not overtighten the Locknut; the Small Wheels
(47) must pivot freely. Repeat with another
wheel assembly and an M8 x 82mm Bolt (95).
Orient the Seat (13) and the Seat Carriage (12)
as shown. Attach the Seat to the Seat Carriage
with four M6 x 16mm Screws (82).
13.
Lubricate two Small Wheels (47) with grease. Slide
a Steel Tube (57) into a 32mm Spacer (46). Orient
the Wheels as shown in the inset drawing, and
slide them onto the ends of the Steel Tube.
Set the Seat Carriage (12) on the Bench Frame
(5). Have one person press the Seat (13) against
the Bench Frame. Press the wheel assembly tight
against the bottom of the Bench Frame and attach
it to the lowest set of holes in the Seat Carriage
with an M8 x 84mm Bolt (60) and an M8 Nylon
Locknut (65).
Do not overtighten the Locknut;
the Small Wheels (47) must pivot freely.
Slide the Seat Pin (45) through the Seat Carriage
(12) and an adjustment hole in the Bench Frame
(5).
15. Orient the Backrest (14) as shown. Attach the
Backrest to the Backrest Frame (15) with four M6
x 38mm Screws (58) and four M6 Washers (77).
14. Press two 25mm Square Inner Caps (54) into the
indicated ends of the Backrest Frame (15). Press
the Backrest Cap (16) onto the other end of the
Backrest Frame. Attach a Plastic Foot (53) to the
Backrest Frame with an M4 Washer (92), and an
M4 x 25mm Screw (56).
Attach a Guard Plate (17) to the inside of the
Backrest Frame (15) with two M4 x 10mm Screws
(96).
Attach the other Guard Plate in the same
manner.
12
13
14
15
13
60
95
Wheel
Assembly
Wheel
Assembly
12
65
65
82
82
45
60
65
47
46
57
47
Adjustment
Hole
12
13
5
16
53
56
92
15
54
17
96
17
15
77
77
58
58
14
Small
Side
Large Side
47
47
57
46
Small
Side
Large Side
47
47
57
46