Weider Pro 9510 English Manual - Page 7

Frame Assembly, Arm Assembly

Get Weider Pro 9510 PDF manuals and user guides View all Weider Pro 9510 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 7 highlights

5. Press the Weight Tube Bumper (64) into the 5 end of the Weight Tube (63). Insert the Weight Tube into the stack of Weights (25). Be sure that the pins on the Weight Tube are sitting in the pin grooves in the top Weight. Lubricate the insides of the holes in the Top Weight (76). Set the Top Weight on the stack of Weights (25). Insert both Weight Guides (62) into the stack of Weights (25). Be sure that the indicated holes in the Weight Guides are at the top. Lubricate 63 Holes 62 76 Pin 64 FRAME ASSEMBLY 25 6. Attach the upper ends of the Weight Guides 6 (62) to the Top Frame (55) with the 5/16" x 6" Bolt (60), two 1/2" x 3/4" Spacers (61), and a 5/16" Nylon Locknut (3). Be sure that the Pulley Bracket (20) is in front of the right Weight Guide (62) as shown. 7. Press a 1" x 7/8" Plastic Bushing (75) onto each welded spacer on the Press Frame (17). Slide the Press Frame into place on the Base (4). Note: This will be a tight fit. The Plastic Bushings should fit on each end of the indicated tube in the Base. Be sure that the 3 1/2" Pulleys (15) are on the indicated side. Lubricate the 3/8" x 8" Bolt (59). Attach the Press Frame (17) to the Base (4) with the 3/8" x 8" Bolt and a 3/8" Nylon Locknut (21). 7 Tube 61 55 3 60 20 62 17 15 4 21 59 Lubricate Welded Spacers 75 7 ARM ASSEMBLY

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
5.
Press the Weight Tube Bumper (64) into the
end of the Weight Tube (63). Insert the
Weight Tube into the stack of Weights (25).
Be sure that the pins on the Weight Tube
are sitting in the pin grooves in the top
Weight.
Lubricate the insides of the holes in the Top
Weight (76). Set the Top Weight on the stack
of Weights (25).
Insert both Weight Guides (62) into the stack
of Weights (25).
Be sure that the indicated
holes in the Weight Guides are at the top.
6.
Attach the upper ends of the Weight Guides
(62) to the Top Frame (55) with the 5/16” x 6”
Bolt (60), two 1/2” x 3/4” Spacers (61), and a
5/16” Nylon Locknut (3).
Be sure that the Pulley Bracket (20) is in
front of the right Weight Guide (62) as
shown.
7.
Press a 1” x 7/8” Plastic Bushing (75) onto
each welded spacer on the Press Frame (17).
Slide the Press Frame into place on the Base
(4).
Note: This will be a tight fit. The
Plastic Bushings should fit on each end of
the indicated tube in the Base. Be sure
that the 3 1/2” Pulleys (15) are on the indi-
cated side.
Lubricate the 3/8” x 8” Bolt (59). Attach the
Press Frame (17) to the Base (4) with the
3/8” x 8” Bolt and a 3/8” Nylon Locknut (21).
7
5
62
Holes
Lubricate
76
Pin
63
64
61
55
3
60
17
15
59
75
21
4
Tube
62
6
FRAME ASSEMBLY
7
ARM ASSEMBLY
20
25
Lubricate
Welded
Spacers