Weider Pro 9940 English Manual - Page 9

of the Long Weight Tube 70. Slide the Weight Tube - weights

Get Weider Pro 9940 PDF manuals and user guides View all Weider Pro 9940 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

12. Place two Weight Bumpers (51) over the indicated 12 holes in the Weight Base (5). Slide a Weight Guide 15 (15) into each of the holes. Attach the indicated Weight Guide (15) to the Weight Base (5) with a 3/8" x 2 3/4" Bolt (46), two 3/8" Flat Washers (48), and a 3/8" Nylon Locknut (50). Slide ten Weights (21) onto the Weight Guides (15). Make sure the Weights are turned so the pin grooves point towards the floor. Press a Weight Tube Bumper (18) into the lower end of the Long Weight Tube (70). Slide the Weight Tube into the center holes in the Weights (21). Slide a Top Weight (16) onto the Weight Guides (15). Note: Make sure the Top Weight is turned so the groove fits over the welded pin on the Weight Tube (70). Groove Pin 21 Pin Grooves 51 48 48 16 70 18 51 50 13. Place the Weight Top Frame (66) on the indicated brackets on the Uprights (1 and 2). Note: The four Weight Guides (15) must be behind the Weight Top Frame, as shown in step 14. Attach the Weight Top Frame (66) to the Butterfly Top Frame (33) with two 3/8" x 2 3/4" Bolts (46), a Support Plate with 4" center holes (94), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. Attach the Weight Top Frame (66) to the bracket on the Butterfly Upright (1) with two 3/8" x 2 3/4" Bolts (46), a Support Plate with 2 1/2" center holes (34), and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 14. Attach the Weight Top Frame (66) to the Press Top Frame (9) with one 3/8" x 2 3/4" Bolt (46), a Support Plate with 4" center holes (94), and a 3/8" Nylon Locknut (50). Slide a 3 1/2" Pulley (24) with a Cable Trap (25) onto a 3/8" x 4" Bolt (78). Insert the Bolt through the Support Plate (94) and hand tighten a 3/8" Nylon Locknut (50) onto it. Attach the Weight Top Frame (66) to the bracket on the Press Upright (2) with two 3/8" x 2 3/4" Bolts (46), a Support Plate with 2 1/2" center holes (34) and two 3/8" Nylon Locknuts (50). Do not tighten the Nylon Locknuts yet. 46 5 13 46 94 33 1 46 34 50 66 50 15 Brackets 14 46 66 34 50 50 9 94 46 25 24 78 2 9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
9
14. Attach the Weight Top Frame (66) to the Press Top
Frame (9) with one 3/8” x 2 3/4” Bolt (46), a Support
Plate with 4” center holes (94), and a 3/8” Nylon
Locknut (50). Slide a 3 1/2” Pulley (24) with a Cable
Trap (25) onto a 3/8” x 4” Bolt (78). Insert the Bolt
through the Support Plate (94) and hand tighten a
3/8” Nylon Locknut (50) onto it.
Attach the Weight Top Frame (66) to the bracket on
the Press Upright (2) with two 3/8” x 2 3/4” Bolts (46),
a Support Plate with 2 1/2” center holes (34) and two
3/8” Nylon Locknuts (50).
Do not tighten the Nylon
Locknuts yet.
14
12. Place two Weight Bumpers (51) over the indicated
holes in the Weight Base (5). Slide a Weight Guide
(15) into each of the holes.
Attach the indicated Weight Guide (15) to the Weight
Base (5) with a 3/8” x 2 3/4” Bolt (46), two 3/8” Flat
Washers (48), and a 3/8” Nylon Locknut (50).
Slide ten Weights (21) onto the Weight Guides (15).
Make sure the Weights are turned so the pin
grooves point towards the floor.
Press a Weight Tube Bumper (18) into the lower end
of the Long Weight Tube (70). Slide the Weight Tube
into the center holes in the Weights (21).
Slide a Top Weight (16) onto the Weight Guides (15).
Note: Make sure the Top Weight is turned so the
groove fits over the welded pin on the Weight
Tube (70).
50
21
46
48
48
5
51
51
70
66
46
78
24
25
50
9
50
34
94
2
13. Place the Weight Top Frame (66) on the indicated
brackets on the Uprights (1 and 2).
Note: The four
Weight Guides (15) must be behind the Weight
Top Frame, as shown in step 14.
Attach the Weight Top Frame (66) to the Butterfly Top
Frame (33) with two 3/8” x 2 3/4” Bolts (46), a
Support Plate with 4” center holes (94), and two 3/8”
Nylon Locknuts (50).
Do not tighten the Nylon
Locknuts yet.
Attach the Weight Top Frame (66) to the bracket on
the Butterfly Upright (1) with two 3/8” x 2 3/4” Bolts
(46), a Support Plate with 2 1/2” center holes (34),
and two 3/8” Nylon Locknuts (50).
Do not tighten the
Nylon Locknuts yet.
13
46
34
46
94
33
1
16
15
18
46
50
66
50
15
Groove
Pin
Brackets
Pin
Grooves
12