Weider Viper 2000 Uk Manual - Page 13

Attach a VKR Armrest 99 to the Left VKR Arm

Get Weider Viper 2000 PDF manuals and user guides View all Weider Viper 2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 13 highlights

30. Attach a VKR Armrest (99) to the Right VKR Arm (101) with two 1/4" x 2" Screws (102) and 1/4" Flat Washers (10). Attach a VKR Armrest (99) to the Left VKR Arm (100) in the same manner. 30 99 101 10 102 100 99 31. Insert a 7" Handle (47) into the Right VKR Arm 31 (101). Attach the Handle with a 5/16" x 2" Bolt (61), two 5/16" Flat Washers (8), and a 5/16" Nylon Locknut (3). Attach the other 7" Handle (47) to the Left VKR Arm (100) in the same manner. 47 61 100 101 8 8 3 47 32. Attach the VKR Backrest (98) to the Rear Upright 32 (82) with two 1/4" x 2 1/2" Screws (43) and two 1/4" Flat Washers (10). 82 43 10 98 33. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in ADJUSTMENT, beginning on page 15 of this manual. Before using the weight system, pull each cable a few times to make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly, locate and correct the problem before using the weight system. IMPORTANT: If the cables are not properly routed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 19 of this manual. 13

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
13
30. Attach a VKR Armrest (99) to the Right VKR Arm
(101) with two 1/4” x 2” Screws (102) and 1/4”
Flat Washers (10).
Attach a VKR Armrest (99) to the Left VKR Arm
(100) in the same manner.
31. Insert a 7” Handle (47) into the Right VKR Arm
(101). Attach the Handle with a 5/16” x 2” Bolt
(61), two 5/16” Flat Washers (8), and a 5/16”
Nylon Locknut (3).
Attach the other 7” Handle (47) to the Left VKR
Arm (100) in the same manner.
32. Attach the VKR Backrest (98) to the Rear Upright
(82) with two 1/4” x 2 1/2” Screws (43) and two
1/4” Flat Washers (10).
30
31
32
99
101
100
10
102
99
61
8
8
3
101
100
47
47
98
82
10
43
33. Make sure that all parts are properly tightened. The use of all remaining parts will be explained in ADJUST-
MENT, beginning on page 15 of this manual. Before using the weight system, pull each cable a few times to
make sure that the cables move smoothly over the pulleys. If one of the cables does not move smoothly,
locate and correct the problem before using the weight system.
IMPORTANT: If the cables are not proper-
ly routed, they may be damaged when heavy weight is used. See the CABLE DIAGRAM on page 19
of this manual.