Weslo 605 Instruction Manual - Page 12

Maintenance And Troubleshooting

Get Weslo 605 PDF manuals and user guides View all Weslo 605 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 12 highlights

MAINTENANCE AND TROUBLESHOOTING Inspect and tighten all parts of the elliptical exerciser regularly. Replace any worn parts immediately. To clean the elliptical exerciser, use a damp cloth and a small amount of mild soap. Important: Keep liquids away from the console and keep the console out of direct sunlight. During storage, remove the batteries from the console. BATTERY REPLACEMENT See the drawing below and locate the Reed Switch (53). Loosen, but do not remove, the indicated M4 x 16mm Screw (42). Slide the Reed Switch slightly toward or away from the Magnet (26) on the flywheel. Then, retighten the Screw. Turn the left Pedal Disc (15) for a moment. Repeat until the console displays correct feedback. When the Reed Switch is correctly adjusted, reattach the Left Side Shield (3) and the Left Pedal Arm (11). If the console display becomes dim, the batteries should be replaced; most console problems are the result of low batteries. To replace the batteries, see assembly step 3 on page 5. HOW TO ADJUST THE REED SWITCH If the console does not display correct feedback, the reed switch should be adjusted. To adjust the reed switch, you must remove the Left Pedal Arm (11) and the Left Side Shield (3). 26 15 53 42 HOW TO ADJUST THE DRIVE BELT 42 56 3 40 11 55 42 22 35 42 Remove the Pedal Arm Bolt Set (40), the M10 x 25mm Patch Screw (22), the M10 Washer (35), and the Wave Washer (55) from the Left Pedal Arm (11). Remove the Left Pedal Arm. Next, remove the two M4 x 25mm Screws (56) and the four M4 x 16mm Screws (42) from the Left Side Shield (3). If the pedals slip while you are pedaling, even when the resistance is adjusted to the highest setting, the Drive Belt (19) may need to be adjusted. To adjust the Drive Belt, you must first remove the left side shield. See HOW TO ADJUST THE REED SWITCH at the left and remove the left side shield. Next, loosen the M8 x 22mm Flat Head Screw (41) and turn the M10 x 60mm 19 Bolt (62) until the Drive Belt (19) is 41 tight. When the Drive Belt is tight, tighten the Flat Head Screw. 62 Then, reattach the left side shield. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
12
Inspect and tighten all parts of the elliptical exerciser
regularly. Replace any worn parts immediately.
To clean the elliptical exerciser, use a damp cloth and
a small amount of mild soap.
Important: Keep liq-
uids away from the console and keep the console
out of direct sunlight. During storage, remove the
batteries from the console.
BATTERY REPLACEMENT
If the console display becomes dim, the batteries
should be replaced; most console problems are the
result of low batteries. To replace the batteries, see
assembly step 3 on page 5.
HOW TO ADJUST THE REED SWITCH
If the console does not display correct feedback, the
reed switch should be adjusted. To adjust the reed
switch, you must remove the Left Pedal Arm (11) and
the Left Side Shield (3).
Remove the Pedal Arm Bolt Set (40), the
M10 x 25mm Patch Screw (22), the M10 Washer (35),
and the Wave Washer (55) from the Left Pedal
Arm (11). Remove the Left Pedal Arm. Next, remove
the two M4 x 25mm Screws (56) and the four
M4 x 16mm Screws (42) from the Left Side Shield (3).
See the drawing below and locate the Reed Switch
(53). Loosen, but do not remove, the indicated
M4 x 16mm Screw (42). Slide the Reed Switch slightly
toward or away from the Magnet (26) on the flywheel.
Then, retighten the Screw. Turn the left Pedal Disc (15)
for a moment. Repeat until the console displays correct
feedback. When the Reed Switch is correctly adjusted,
reattach the Left Side Shield (3) and the Left Pedal
Arm (11).
HOW TO ADJUST THE DRIVE BELT
If the pedals slip while you are pedaling, even when
the resistance is adjusted to the highest setting, the
Drive Belt (19) may need to be adjusted. To adjust the
Drive Belt, you must first remove the left side shield.
See HOW TO ADJUST THE REED SWITCH at the
left and remove the left side shield.
Next, loosen the
M8 x 22mm Flat
Head Screw (41)
and turn the
M10 x 60mm
Bolt (62) until the
Drive Belt (19) is
tight. When the
Drive Belt is tight,
tighten the Flat
Head Screw.
Then, reattach
the left side
shield.
MAINTENANCE AND TROUBLESHOOTING
42
56
42
42
22
55
3
40
15
41
62
19
35
11
26
53
42