Whirlpool WDT730HAM Installation Instructions - Page 12

Connect Water Line to Fill Valve, Measure cabinet opening, Adjust leveling legs

Page 12 highlights

11. Measure cabinet opening 12. Adjust leveling legs Measure height of cabinet opening from underside of countertop to floor where dishwasher will be installed. Be sure to measure the lowest point on the underside of the countertop and the highest point on the floor. Dishwasher Height Adjustment Chart Cabinet-opening Front legs height Rear legs height height A B 331/2" (851 mm) 3/8" (9.8 mm) Remove legs and spacers. 34" (864 mm) 7/8" (22 mm) 1" (25.4 mm) 341/2" (876 mm) 11/8" (28.8 mm) 11/4" (31.3 mm) Front legs - A Rear legs - B Refer to the "Dishwasher Height Adjustment Chart" for height of leveling legs needed for your cabinet opening. 13. Remove plastic rail cover A A. Plastic rail cover Remove and discard the plastic rail cover on each side of the dishwasher frame. To remove the plastic rail cover, push upward and back to unsnap it from the dishwasher frame. Connect Water Line to Fill Valve - For Copper Line, begin with step 14 - For Flexible Line, begin with step 16 14. Copper water line B Adjust both front and back leveling legs to the same height. NOTE: If the minimum cabinet opening height is less than 337/8" (860 mm), the rear leveling legs and spacers can be removed for additional clearance. This will allow the dishwasher to fit into a 331/2" (851 mm) high cabinet opening, but the dishwasher will be more difficult to move. (Measurements are approximate. Rear and front leveling legs are preset at the factory for 341/2" [876 mm].) If using copper tubing, measure overall length of copper tubing required to reach the water supply, cut to length, and attach with compression fittings. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56

12
11. Measure cabinet opening
Measure height of cabinet opening from underside of
countertop to floor where dishwasher will be installed. Be
sure to measure the lowest point on the underside of the
countertop and the highest point on the floor.
Dishwasher Height Adjustment Chart
Cabinet-opening
height
Front legs height
A
Rear legs height
B
33
1
/
2
" (851 mm)
3/8" (9.8 mm)
Remove legs and
spacers.
34" (864 mm)
7/8" (22 mm)
1" (25.4 mm)
34
1
/
2
" (876 mm)
1
1
/
8
" (28.8 mm)
1
1
/
4
" (31.3 mm)
Front legs – A
Rear legs – B
B
Adjust both front and back leveling legs to the same height.
NOTE:
If the minimum cabinet opening height is less than
33
7
/
8
" (860 mm), the rear leveling legs and spacers can be
removed for additional clearance. This will allow the
dishwasher to fit into a 33
1
/
2
" (851 mm) high cabinet opening,
but the dishwasher will be more difficult to move.
(Measurements are approximate. Rear and front leveling
legs are preset at the factory for 34
1
/
2
" [876 mm].)
12.
Adjust leveling legs
Refer to the “Dishwasher Height Adjustment Chart” for height
of leveling legs needed for your cabinet opening.
13. Remove plastic rail cover
A
A. Plastic rail cover
Remove and discard the plastic rail cover on each side of the
dishwasher frame. To remove the plastic rail cover, push
upward and back to unsnap it from the dishwasher frame.
Connect Water Line to Fill Valve
– For Copper Line, begin with step 14
– For Flexible Line, begin with step 16
14. Copper water line
If using copper tubing, measure overall length of copper
tubing required to reach the water supply, cut to length, and
attach with compression fittings.