Whirlpool WED6600VU Use and Care Manual - Page 16

an additional - washers

Get Whirlpool WED6600VU - 29-in Electric Dryer PDF manuals and user guides
UPC - 883049141251
View all Whirlpool WED6600VU manuals
Add to My Manuals
Save this manual to your list of manuals

Page 16 highlights

5. Attach "Y" connector to brass male end of small hose. Screw on coupling by hand until it is seated on connector. 6. Attach straight end of long hose to "Y" connector. 7. Attach washer cold inlet hose to other end of "Y" connector. Screw on coupling by hand until it is seated on connector. 8. Using pliers, tighten the couplings with an additional twothirds turn. Check the levelness of the dryer by first placing a level on the top of the dryer near the console. A. Inlet to cold water NOTE: Do not overtighten. Damage to the coupling can result. 9. Attach angled end of long hose to fill valve at bottom of dryer back panel. Screw on coupling by hand until it is seated on fill valve connector. 10. Using pliers, tighten the coupling with an additional twothirds turn. Then, by placing a level in the crease on the side of the dryer between the top of the dryer and the dryer cabinet, check the levelness from front to back. If the dryer is not level, prop up the dryer using a wood block. Use a wrench to adjust the legs up or down and check again for levelness. NOTE: Do not overtighten. Damage to the coupling can result. 11. Check that the water faucets are on. 12. Check for leaks around "Y" connector, faucet and hoses. 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
5.
Attach
"Y" connector
to brass male end of small hose. Screw
on coupling
by hand until it is seated
on connector.
6.
Attach
straight end of long hose to "Y" connector.
7.
Attach
washer cold inlet hose to other end of "Y" connector.
Screw
on coupling
by hand until it is seated on connector.
8.
Using pliers, tighten
the couplings
with an additional
two-
thirds turn.
Check the levelness of the dryer by first placing
a level on the top
of the dryer
near the console.
A. Inlet to cold
water
NOTE: Do not overtighten.
Damage to the coupling
can
result.
9.
Attach
angled end of long hose to fill valve at bottom
of dryer
back panel. Screw
on coupling
by hand until it is seated
on fill
valve connector.
10. Using pliers, tighten
the coupling
with
an additional
two-
thirds turn.
Then, by placing
a level in the crease on the side of the dryer
between the top of the dryer and the dryer cabinet,
check the
levelness from front to back.
If the dryer is not level, prop up the dryer
using a wood
block.
Use a wrench
to adjust the legs up or down
and check again for
levelness.
NOTE: Do not overtighten.
Damage to the coupling
can
result.
11. Check that the water faucets
are on.
12. Check for leaks around
"Y" connector,
faucet
and hoses.
16