Whirlpool WFW9620HW Owners Manual - Page 18

REMOVING THE DISPENSER cont., Single-Load Dispenser Drawer, CLEANING LOAD & GO, CONTAINERS,

Get Whirlpool WFW9620HW PDF manuals and user guides View all Whirlpool WFW9620HW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

REMOVING THE DISPENSER (cont.) Single-Load Dispenser Drawer Removing the Dispenser To remove: 1. Pull dispenser drawer out until it stops. 2. Press down on the release tab and pull straight out to remove the dispenser. CLEANING LOAD & GO™ CONTAINERS It is recommended that you rinse out the Load & Go™ containers when refilling, when changing detergent types or concentrations, or when the washer will not be used for an extended period. 1. Pull the dispenser drawer out until it stops. 2. Lift out the Load & Go™ containers. 3. Lift the fill lid and flush interior thoroughly with warm water. 3. Lift off cover panel by pulling straight up. To replace: 1. Position cover panel back onto posts on dispenser. Apply slight pressure on cover panel to seat it. 2. Align edges of dispenser with guides in washer; then slide dispenser back into slot. 4. Allow to air dry. IMPORTANT: Containers are not dishwasher safe. WATER INLET HOSES Replace inlet hoses after five years of use to reduce the risk of hose failure. Periodically inspect and replace inlet hoses if bulges, kinks, cuts, wear, or leaks are found. When replacing your inlet hoses: Mark the date of replacement on the label with a permanent marker. Check that the old washers are not stuck on the washer inlet valves. Use new washers in the new inlet hoses to ensure a proper seal. 18

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
18
REMOVING THE DISPENSER (cont.)
Removing the Dispenser
To remove:
1.
Pull dispenser drawer out until it stops.
2.
Press down on the release tab and pull straight out
to remove the dispenser.
3.
Lift off cover panel
by pulling straight up.
To replace:
1.
Position cover panel back
onto posts on dispenser.
Apply slight pressure on
cover panel to seat it.
2.
Align edges of dispenser
with guides in washer;
then slide dispenser
back into slot.
Single-Load Dispenser Drawer
It is recommended that you rinse out the Load & Go
™
containers when refilling, when changing detergent types or
concentrations, or when the washer will not be used for an
extended period.
1.
Pull the dispenser drawer out until it stops.
2.
Lift out the Load & Go
™
containers.
3.
Lift the fill lid and flush interior thoroughly with warm water.
4.
Allow to air dry.
IMPORTANT:
Containers are not dishwasher safe.
CLEANING LOAD & GO
™
CONTAINERS
Replace inlet hoses after five years of use to reduce the risk
of hose failure. Periodically inspect and replace inlet hoses
if bulges, kinks, cuts, wear, or leaks are found.
When replacing your inlet hoses:
Mark the date of replacement on the label with a permanent
marker.
Check that the old washers are not stuck on the washer inlet
valves.
Use new washers in the new inlet hoses to ensure a proper seal.
WATER INLET HOSES