Xerox 6125N User Guide - Page 10

Operational Safety, Printer Location, Printer Clearance, Operational Guidelines

Get Xerox 6125N - Phaser Color Laser Printer PDF manuals and user guides
UPC - 095205739275
View all Xerox 6125N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

User Safety Operational Safety Your printer and supplies were designed and tested to meet strict safety requirements. These include safety agency examination, approval, and compliance with established environmental standards.Your attention to the following safety guidelines helps to ensure the continued, safe operation of your printer. Printer Location Place the printer in a dust-free area within a temperature range of 50° F to 90° F (10° C to 32° C) and a relative humidity range of 15 percent to 85 percent. Humidity should be 70 percent or below at 90° F, and temperature should be 82° F or below at 85 percent humidity. Note: Sudden temperature fluctuations can affect print quality. Rapid heating of a cold room can cause condensation inside the machine, directly interfering with image transfer. Printer Clearance Place the printer in an area where there is adequate space for ventilation, operation, and servicing. The recommended minimal spacing is: Overhead Clearance: ■ 20 cm (7.9 in.) above the printer Total Height Requirements: ■ Printer: 58.9 cm (23.2 in.) Other Clearances: ■ 10 cm (3.9 in.) behind the printer ■ 60 cm (23.6 in.) in front of the printer ■ 10 cm (3.9 in.) on the left side of the printer ■ 25 cm (9.8 in.) on the right side of the printer Operational Guidelines ■ Do not block or cover the slots and openings on the printer. The printer may overheat without adequate ventilation. ■ For optimum performance, use the printer at elevations below 3,500 m (11,480 ft.). ■ Do not place the printer near a heat source. ■ Do not place the printer in direct sunlight to avoid exposing light-sensitive components when the doors are open. ■ Do not place the printer in line with the cold air flow from an air conditioning system. Phaser® 6125 Color Laser Printer 1-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
User Safety
Phaser® 6125 Color Laser Printer
1-4
Operational Safety
Your printer and supplies were designed and tested to meet strict safety requirements. These
include safety agency examination, approval, and compliance with established environmental
standards.Your attention to the following safety guidelines helps to ensure the continued, safe
operation of your printer.
Printer Location
Place the printer in a dust-free area within a temperature range of 50° F to 90° F (10° C to
32° C) and a relative humidity range of 15 percent to 85 percent.
Humidity should be 70 percent or below at 90° F, and temperature should be 82° F or below at
85 percent humidity.
Note:
Sudden temperature fluctuations can affect print quality. Rapid heating of a cold room
can cause condensation inside the machine, directly interfering with image transfer.
Printer Clearance
Place the printer in an area where there is adequate space for ventilation, operation, and
servicing. The recommended minimal spacing is:
Overhead Clearance:
■
20 cm (7.9 in.) above the printer
Total Height Requirements:
■
Printer: 58.9 cm (23.2 in.)
Other Clearances:
■
10 cm (3.9 in.) behind the printer
■
60 cm (23.6 in.) in front of the printer
■
10 cm (3.9 in.) on the left side of the printer
■
25 cm (9.8 in.) on the right side of the printer
Operational Guidelines
■
Do not block or cover the slots and openings on the printer. The printer may overheat
without adequate ventilation.
■
For optimum performance, use the printer at elevations below 3,500 m (11,480 ft.).
■
Do not place the printer near a heat source.
■
Do not place the printer in direct sunlight to avoid exposing light-sensitive components
when the doors are open.
■
Do not place the printer in line with the cold air flow from an air conditioning system.