Xerox M123 System Administration Guide - Page 69

Select [TCP/IP - Get IP Address], and then [Change Settings

Get Xerox M123 - WorkCentre B/W Laser PDF manuals and user guides View all Xerox M123 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 69 highlights

EtherTalk Installation Initially, boot the EtherTalk port. 1. Connect the machine to the network. 2. Display the [System Settings] screen. NOTE: For more information about how to display the [System Setting] screen, refer to the Setups chapter of the User Guide. 3. Select [Network Settings]. 4. Select [Port Settings]. 5. Select [EtherTalk], and then [Change Settings]. 6. Select [Port Status] and then [Change Settings]. 7. Select [Enabled], and then [Save]. Next, establish TCP/IP. 1. Display the [System Settings] screen. NOTE: For more information about how to display the [System Setting] screen, refer to the Setups chapter of the User Guide. 2. Select [Network Settings]. 3. Select [Protocol Settings]. 4. Select [TCP/IP - Get IP Address], and then [Change Settings]. 5. Select a method for establishing an IP address from [DHCP], [BOOTP], [RARP], [DHCP/Autonet], or [Manual], and then select [Save]. NOTE: Use the DHCP server together with the Windows Internet Name Server (WINS) server. If you selected [Manual] in step 5, then complete steps 6 to 11 to enter the [Protocol Settings]. Otherwise, complete step 14. 6. Select [TCP/IP - IP Address], and then [Change Settings]. 7. Use the keypad on the screen to enter the IP Address for the machine in the format "xxx.xxx.xxx.xxx". Enter relevant values (0 to 255) into the highlighted field and select [Next]. The next 3 digits are highlighted. When you have finished entering all values, select [Save]. 8. Select [TCP/IP - Subnet Mask], and then [Change Settings]. 9. Using the same method as in step 7, enter the Subnet Mask. 10. Select [TCP/IP - Gateway Address] and [Change Settings]. 11. Using the same method as in step 7, enter the Gateway Address. NOTE: If you do not wish to set the Gateway Address, enter "0.0.0.0". 12. Select [TCP/IP - IP Filter], then [Change Settings]. 13. Select [On] to filter access to the machine. Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 System Administration Guide 69

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
EtherTalk Installation
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 System Administration Guide
69
Initially, boot the EtherTalk port.
1.
Connect the machine to the network.
2.
Display the [System Settings] screen.
NOTE:
For more information about how to display the [System Setting] screen, refer
to the Setups chapter of the User Guide.
3.
Select [Network Settings].
4.
Select [Port Settings].
5.
Select [EtherTalk], and then [Change Settings].
6.
Select [Port Status] and then [Change Settings].
7.
Select [Enabled], and then [Save].
Next, establish TCP/IP.
1.
Display the [System Settings] screen.
NOTE:
For more information about how to display the [System Setting] screen, refer
to the Setups chapter of the User Guide.
2.
Select [Network Settings].
3.
Select [Protocol Settings].
4.
Select [TCP/IP – Get IP Address], and then [Change Settings].
5.
Select a method for establishing an IP address from [DHCP], [BOOTP], [RARP],
[DHCP/Autonet], or [Manual], and then select [Save].
NOTE:
Use the DHCP server together with the Windows Internet Name Server
(WINS) server.
If you selected [Manual] in step 5, then complete steps 6 to 11 to enter the [Protocol
Settings]. Otherwise, complete step 14.
6.
Select [TCP/IP – IP Address], and then [Change Settings].
7.
Use the keypad on the screen to enter the IP Address for the machine in the
format “xxx.xxx.xxx.xxx”. Enter relevant values (0 to 255) into the highlighted field
and select [Next]. The next 3 digits are highlighted. When you have finished
entering all values, select [Save].
8.
Select [TCP/IP – Subnet Mask], and then [Change Settings].
9.
Using the same method as in step 7, enter the Subnet Mask.
10.
Select [TCP/IP – Gateway Address] and [Change Settings].
11.
Using the same method as in step 7, enter the Gateway Address.
NOTE:
If you do not wish to set the Gateway Address, enter “0.0.0.0”.
12.
Select [TCP/IP - IP Filter], then [Change Settings].
13.
Select [On] to filter access to the machine.