Xerox M123 System Administration Guide - Page 81

Network Communication Setup, Workstation Setup, Test Print

Get Xerox M123 - WorkCentre B/W Laser PDF manuals and user guides View all Xerox M123 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 81 highlights

TCP/IP (LPD or Port9100) Installation Network Communication Setup Enable the following ports using the touch screen or CentreWare Internet Services. • Printing through LPD: LPD port • Printing through Port9100: Port9100 port Set the IP address using the touch screen. NOTE: CentreWare Internet Services allows more detailed settings. For instructions, refer to the CentreWare Internet Services chapter of the User Guide. Workstation Setup This requires the workstations in the networking environment to be configured to communicate with the machine. Test Print A print job should be submitted to make sure that the machine has been installed and configured correctly. Network Communication Setup This section describes how to set up the network communication parameters of the machine. At the machine, perform these steps. NOTE: Keep the SNMP port enabled while you use the machine on the TCP/IP network. NOTE: CentreWare Internet Services can also be used to configure the machine. Refer to the CentreWare Internet Services chapter of the User Guide. Initially, boot the LPD port or Port9100. 1. Connect the machine to the network. 2. Display the [System Settings] screen. NOTE: For more information about how to display the [System Settings] screen, refer to the Setups chapter of the User Guide. 3. Select [Network Settings]. 4. Select [Port Settings]. 5. If you are using the LPD port, select [LPD] and [Change Settings]. If you are using Port9100, select [Port9100] and [Change Settings]. 6. If you are using the LPD port, select [Port Status] and [Change Settings]. If you are using Port9100, select [Port Status] and [Change Settings]. 7. Select [Enabled] and [Save]. Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 System Administration Guide 81

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
TCP/IP (LPD or Port9100) Installation
Xerox CopyCentre/WorkCentre/WorkCentre Pro 123/128/133 System Administration Guide
81
Network Communication Setup
Enable the following ports using the touch screen or CentreWare Internet Services.
•
Printing through LPD: LPD port
•
Printing through Port9100: Port9100 port
Set the IP address using the touch screen.
NOTE:
CentreWare Internet Services allows more detailed settings. For instructions,
refer to the CentreWare Internet Services chapter of the User Guide.
Workstation Setup
This requires the workstations in the networking environment to be configured to
communicate with the machine.
Test Print
A print job should be submitted to make sure that the machine has been installed and
configured correctly.
Network Communication Setup
This section describes how to set up the network communication parameters of the
machine.
At the machine, perform these steps.
NOTE:
Keep the SNMP port enabled while you use the machine on the TCP/IP
network.
NOTE:
CentreWare Internet Services can also be used to configure the machine.
Refer to the CentreWare Internet Services chapter of the User Guide.
Initially, boot the LPD port or Port9100.
1.
Connect the machine to the network.
2.
Display the [System Settings] screen.
NOTE:
For more information about how to display the [System Settings] screen, refer
to the Setups chapter of the User Guide.
3.
Select [Network Settings].
4.
Select [Port Settings].
5.
If you are using the LPD port, select [LPD] and [Change Settings]. If you are using
Port9100, select [Port9100] and [Change Settings].
6.
If you are using the LPD port, select [Port Status] and [Change Settings]. If you
are using Port9100, select [Port Status] and [Change Settings].
7.
Select [Enabled] and [Save].