Yamaha CLP-525 Owner's Manual - Page 29

Keyboard Stand Assembly

Get Yamaha CLP-525 PDF manuals and user guides View all Yamaha CLP-525 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

Keyboard Stand Assembly CAUTION • Assemble the unit on a hard and flat floor with ample space. • Be careful not to confuse parts, and be sure to install all parts in the correct orientation. Please assemble the unit in accordance with the sequence given below. • Assembly should be carried out by at least two persons. • Be sure to use only the included screws of the specified sizes. Do not use any other screws. Use of incorrect screws can cause damage or malfunction of the product. • Be sure to tighten all screws upon completing assembly of the unit. • To disassemble the unit, reverse the assembly sequence given below. Have a Phillips-head (+) screwdriver of the appropriate size ready. 1. Attach (finger-tighten) C to D and E. 1-3 Remove all parts from the package and make sure you have all of the items. Foamed styrol pads Remove foamed styrol pads from the package, position them on the floor, then place A on top of them. Position the pads so that they will not hide the connectors on the bottom of A. Bundled pedal cord inside 1-1 1-1 Untie and straighten out the bundled pedal cord. Don't discard the vinyl tie. You will need it later in step 6. 1-2 Align D and E with each end of C. 1-3 Attach D and E to C by finger-tightening the long screws (6 x 20 mm). 2. Attach B. 2-1 2-2 6 x 20 mm long screws x 4 Power cord x 1 4 x 12 mm thin screws x 2 4 x 20 mm tapping screws x 4 6 x 16 mm short screws x 6 AC power adaptor x 1 The power cord and adaptor may not be included, or may look different from the illustration above, depending on your particular area. Please check with your Yamaha dealer. Cord holders x 2 4 × 10 mm thin screws x 2 Headphone hanger x 1 2-3 2-2 2-2 2-1 Align the screw holes on the upper side of B with the bracket holes on D and E, then attach the upper corners of B to D and E by finger-tightening two thin screws (4 x 12 mm). 2-2 While pushing the lower part of D and E from outside, secure the bottom ends of B using two tapping screws (4 x 20 mm). 29 CLP-525 Owner's Manual

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
29
CLP-525 Owner’s Manual
Keyboard Stand Assembly
CAUTION
•
Assemble the unit on a hard and flat floor with ample space.
•
Be careful not to confuse parts, and be sure to install all
parts in the correct orientation. Please assemble the unit in
accordance with the sequence given below.
•
Assembly should be carried out by at least two persons.
•
Be sure to use only the included screws of the specified
sizes. Do not use any other screws. Use of incorrect screws
can cause damage or malfunction of the product.
•
Be sure to tighten all screws upon completing assembly of
the unit.
•
To disassemble the unit, reverse the assembly sequence
given below.
Remove all parts from the package and make sure you
have all of the items.
1.
Attach (finger-tighten) C to D and
E.
1-1
Untie and straighten out the bundled pedal
cord.
Don’t discard the vinyl tie. You will need it later in
step 6.
1-2
Align D and E with each end of C.
1-3
Attach D and E to C by finger-tightening
the long screws (6 x 20 mm).
2.
Attach B.
2-1
Align the screw holes on the upper side of B
with the bracket holes on D and E, then
attach the upper corners of B to D and E by
finger-tightening two thin screws (4 x 12
mm).
2-2
While pushing the lower part of D and E
from outside, secure the bottom ends of B
using two tapping screws (4 x 20 mm).
Have a Phillips-head (+) screwdriver of the appropriate size
ready.
Foamed styrol pads
Remo
v
e foamed styrol pads from the package, position them
on the floor, then place A on top of them. Position the pads so
that they
w
ill not hide the connectors on the
b
ottom of A.
B
u
ndled pedal cord inside
6 x 20 mm long scre
w
s x 4
4 x 12 mm thin scre
w
s x 2
4 x 20 mm tapping scre
w
s x 4
6 x 16 mm short scre
w
s x 6
Cord holders x 2
Po
w
er cord x 1
AC po
w
er adaptor x 1
The po
w
er cord and adaptor may
not
b
e incl
u
ded, or may look
different from the ill
u
stration
a
b
o
v
e, depending on yo
u
r
partic
u
lar area. Please check
w
ith
yo
u
r Yamaha dealer.
4 × 10 mm
thin scre
w
s x 2
Headphone hanger x 1
1-1
1-3
2-1
2-2
2-2
2-3
2-2