Yamaha D2040 D2040 Owners Manual Image - Page 17

left/right

Get Yamaha D2040 PDF manuals and user guides View all Yamaha D2040 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Parameter 1. Parameter Editing (P.EO/D.ATT, LIMIT/COMP, DELAY/POLARITY, FILTER keys) ® Use the UR keys and the parameter selection keys to determine the parameter you wish to edit. The parameter will be displayed on the LCD screen. The red LED of the key for the parameter under selection will also light up. L PARAM LINK PER D. ATT .mo DELAY PO RRY CD LM I IT COMP FILTER use UR keys press key for desired parameter 0 Use the parameter left/right cursor keys to bring the cursor on the LCD screen ("_") to the desired parameter. The settings made manually with the knobs can be written (stored) to memory the same as parameter values. O When memory settings are recalled, the knobs are automatically set to those settings. ® When the OUTPUT LEVEL category is selected in utility mode the LCD screen will display the output level settings. These settings can be altered with the parameter up/down keys. a n 1. Channel Mute ® It is possible to digitally mute the output channel. Press the MUTE key for the channel you wish to mute. The red LED of the key will light up and the channel will be muted. V PARAMETER C) Use the parameter up/down keys to increase or decrease the parameter value under selection. 6 PARAMETER ® Once in parameter edit mode there is no special key to return to title display. © Parameter link (described later) can also be used. 2. Output Level ® The output control knob controls the analog output that results after D/A conversion. All knobs are motor driven but can also be set manually. ® Press the MUTE key again and the LED will turn off, showing that the muting has been stopped. C) It is not possible to write (store) mute settings to memory. The mute key stays effective after turning the power off and after memory recall. 1. Parameter Link ® Press first and hold the L or R key, depending on what side you wish to make the master in setting the parameter. Its red LED will light up. While holding the master key, press the other side's key (slave) and its red LED will begin blinking. Let go of both keys and the link has been established. light up light up blinking PARAM LINK PARAM LINK 10 16

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
Parameter
1.
Parameter
Editing
(P.EO/D.ATT,
LIMIT/COMP,
DELAY/POLARITY,
FILTER
keys)
®
Use
the
UR
keys
and
the
parameter
selection
keys
to
determine
the
parameter
you
wish
to
edit.
The
parameter
will
be
displayed
on
the
LCD
screen.
The
red
LED
of
the
key
for
the
parameter
under
selection
will
also
light
up.
The
settings
made
manually
with
the
knobs
can
be
written
(stored)
to
memory
the
same
as
parameter
values.
O
When
memory
settings
are
recalled,
the
knobs
are
automatically
set
to
those
settings.
®
When
the
OUTPUT
LEVEL
category
is
selected
in
utility
mode
the
LCD
screen
will
display
the
output
level
settings.
These
settings
can
be
altered
with
the
parameter
up/down
keys.
CD
PER
D.
ATT
LI
MIT
COMP
.mo
DELAY
PO
RRY
FILTER
a
n
L
PARAM
LINK
use
UR
keys
press
key
for
desired
parameter
0
Use
the
parameter
left/right
cursor
keys
to
bring
the
cursor
on
the
LCD
screen
("_")
to
the
desired
parameter.
V
PARAMETER
C)
Use
the
parameter
up/down
keys
to
increase
or
decrease
the
parameter
value
under
selection.
6
PARAMETER
®
Once
in
parameter
edit
mode
there
is
no
special
key
to
return
to
title
display.
©
Parameter
link
(described
later)
can
also
be
used.
2.
Output
Level
®
The
output
control
knob
controls
the
analog
output
that
results
after
D/A
conversion.
All
knobs
are
motor
driven
but
can
also
be
set
manually.
10
1.
Channel
Mute
®
It
is
possible
to
digitally
mute
the
output
channel.
Press
the
MUTE
key
for
the
channel
you
wish
to
mute.
The
red
LED
of
the
key
will
light
up
and
the
channel
will
be
muted.
®
Press
the
MUTE
key
again
and
the
LED
will
turn
off,
showing
that
the
muting
has
been
stopped.
C)
It
is
not
possible
to
write
(store)
mute
settings
to
memory.
The
mute
key
stays
effective
after
turning
the
power
off
and
after
memory
recall.
1.
Parameter
Link
®
Press
first
and
hold
the
L
or
R
key,
depending
on
what
side
you
wish
to
make
the
master
in
setting
the
parameter.
Its
red
LED
will
light
up.
While
holding
the
master
key,
press
the
other
side's
key
(slave)
and
its
red
LED
will
begin
blinking.
Let
go
of
both
keys
and
the
link
has
been
established.
light
up
light
up
blinking
PARAM
LI
NK
PARAM
LINK
16