Yamaha MGP16X Owner's Manual - Page 30

Appendix Specifications Electrical Characteristics 0 dBu=0.775 Vrms, 0 dBV=1 Vrms All faders are set to nominal position if not specified. (Nominal position is adjusted to a position that is 10 dB lower than the maximum position) Output impedance of signal generator(Rs)=150 ohms, Output load impedance=10k ohms (TRS phone output), 600 ohms (XLR output) Frequency Response Total Harmonic Distortion Noise*1 Crosstalk at 1 kHz*2 CH INPUT STEREO OUT GROUP OUT AUX SEND FX SEND STEREO OUT Adjacent Input Input to Output CH INPUT MIC to Maximum Voltage Gain (1 kHz)*3 RETURN to 2TR IN to 20 Hz-20 kHz, refer to the nominal output level @1 kHz GAIN: min (MONO CH, STEREO CH) STEREO OUT +14 dBu@20 Hz-20 kHz, GAIN: min EIN (Equivalent Input Noise): Rs=150 ohms, GAIN: max STEREO and GROUP master faders are at nominal position and all of bus assign switches are off. AUX and FX master controls are at nominal position, and all of CH mix controls are at minimum position. Residual Output Noise Between input channels STEREO OUT L/R, PAN: panned hard left or right CH INSERT OUT STEREO OUT GROUP OUT REC OUT MONITOR OUT PHONES OUT AUX SEND (AUX2: PRE) AUX SEND (AUX2: POST) FX SEND STEREO OUT AUX SEND STEREO OUT MONITOR OUT +0.5/-1.0 0.02 -128 -92 -83 -102 -74 -74 60 84 84 62 80 69 76 86 86 16 12 28 34 UNIT dB % dBu dBu dBu dBu dB dB dB dB dB dB dB dB dB dB dB dB dB dB dB *1 Noise is measured with an A-Weighting filter. *2 Crosstalk is measured with a 1 kHz band pass filter. *3 Maximum voltage gain is measured under the condition that all faders and GAIN controls are at maximum. PAN/BAL controls are panned hard left or right. General Specifications Supported iPod/iPhone models (as of Dec. 2011) Input Channel HPF HIGH Input Channel EQ MID LOW Input Channel Compressor Signal Indicator CH INPUT LED Level Meter Phantom Power Power Supply Requirements Power Consumption Dimensions (W x H x D) Weight *iPod classic, iPod touch (1st - 4th generation), iPod nano (2nd - 6th generation), iPhone 4S, iPhone 4, iPhone 3GS, iPhone 3G, iPhone 100 Hz, 12 dB/oct 8 kHz, shelving MGP16X CHs 1-8, 13-16: 250 Hz to 5 kHz, peaking MGP16X CHs 9-12: 2.5 kHz, peaking MGP12X CHs 1-4, 9-12: 250 Hz to 5 kHz, peaking MGP12X CHs 5-8: 2.5 kHz, peaking 125 Hz, shelving Parameters (ratio, threshold, output gain) are controlled by one knob. PEAK indicator (red) SIG indicator (green) PEAK lights if the signal comes within 3 dB of the clipping level. 2 x 12 segments LED meter (PEAK, +10, +6, +3, 0, -3, -6, -10, -15, -20, -25, -30 dB) Metering point: post stereo master fader or pre monitor level +48V 100-240 V 50/60 Hz, auto sensing, IEC input MGP16X: 55 watts max MGP12X: 45 watts max MGP16X: 447 mm x 143 mm x 495 mm (17.6" x 5.6" x 19.5") MGP12X: 348 mm x 143 mm x 495 mm (13.7" x 5.6" x 19.5") MGP16X: 9.0 kg (19.8 lb) MGP12X: 7.5 kg (16.5 lb) * The device may not function depending on your iPod/iOS software version. For updated information about supported software versions, check the Yamaha Pro Audio website (http://www.yamahaproaudio.com/). 30 MGP16X/MGP12X Owner's Manual