Yamaha MT400 Owner's Manual - Page 21
Mixdown, Connecting a master recorder, Sending the tape playback sound to the, input channels
View all Yamaha MT400 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 21 highlights
20 Mixdown After you have recorded all tracks, you are ready to mix them into a stereo mix, which you will record to a stereo master recorder. POWER DC 12V ON/ OFF SYNC OUT MONITOR OUT STEREO OUT R L R L 0 7 2 1 INSERT I/O MIC/LINE INPUT 2 INSERT I/O 3 1 STEREO INPUT 4 5L 6R 7L 8R 1 AUX SEND 1 2 GAIN LINE HIGH -12 MID -12 LOW -12 AUX 1 0 AUX 2 0 MIX 1 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 2 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 3 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 4 5L-6R 7L-8R LEVEL LEVEL MIC 0 10 0 10 +12 MULTITRACK CASSETTE RECORDER +12 +6 +3 0 -5 -10 REC 1 2 3 4 L R +12 10 10 CUE TAPE SPEED CONTROL PITCH 4.8/ 9.5 - + ON OFF SYNC ZERO STOP ON OFF REC SELECT 1 2 3 4 OFF OFF OFF OFF L R L R +6 POWER +3 0 -5 -10 METER SELECT 4TR STEREO 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP LEVEL PAN PAN PAN PAN MIN MONITOR/PHONES STEREO ST+CUE CUE MAX L R L R L R L R 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 STEREO 10 9 8 7 6 5 4 3 2 1 0 NOISE REDUCTION SYSTEM REC PLAY REW FF STOP PAUSE 4 3 5 6 Connecting a master recorder 1 Connect the STEREO OUT jacks on the rear panel of the MT400 to the input jacks of a master recorder, and connect the output jacks of the master recorder to the STEREO INPUT 5L/6R jacks on the top panel of the MT400. Sending the tape playback sound to the input channels 2 Set the [INPUT-FLIP] switches on Input Channels 1-4 to "TAPE ( )". When the [INPUT-FLIP] switches are set to "TAPE ( )", the playback sound of the corresponding tracks are sent to the input channels, where you can adjust tonal quality with the EQ controls and stereo position with the PAN control. The playback sound sent to Input Channels 1-4 are routed to the STEREO bus for stereo mix and output from the SETEREO OUT jacks. 3 Set the monitor select switch to "STEREO". The stereo bus is selected as a monitoring source, and you can listen to the STEREO OUT signals via headphones or an audio system connected to the PHONES or MONITOR OUT jacks. 4 Set the [METER SELECT] switch to "STEREO". The level meters L and R on the left indicate the level of the Stereo bus signal output from the STEREO OUT jacks. -Owner's Manual