Yamaha MT400 Owner's Manual - Page 41

40 Recording a SYNC Signal on the Tape 8 2 1 INSERT I/O MIC/LINE INPUT 2 INSERT I/O 3 STEREO INPUT 4 5L 6R 7L 8R AUX SEND 1 2 GAIN LINE HIGH -12 MID -12 LOW -12 AUX 1 0 AUX 2 0 MIX 1 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 2 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 3 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 4 5L-6R 7L-8R LEVEL LEVEL MIC 0 10 0 10 +12 MULTITRACK CASSETTE RECORDER +12 +6 +3 0 -5 -10 REC 1 2 3 4 L R +12 10 10 CUE TAPE SPEED CONTROL PITCH 4.8/ 9.5 - + ON OFF SYNC ZERO STOP ON OFF REC SELECT 1 2 3 4 OFF OFF OFF OFF L R L R +6 POWER +3 0 -5 -10 METER SELECT 4TR STEREO 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP LEVEL PAN PAN PAN PAN MIN MONITOR/PHONES STEREO ST+CUE CUE MAX L R L R L R L R 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 STEREO 10 9 8 7 6 5 4 3 2 1 0 NOISE REDUCTION SYSTEM REC PLAY REW FF STOP PAUSE 3 4 0 5 CA 1 Connect the MT400 to the FSK/MIDI converter or the SMPTE/MTC converter as shown in the diagrams on pages 38 and 39. 2 Set the [INPUT-FLIP] switch on Input Channel 4 to "MIC/LINE ( )". 3 Set the [REC SELECT] switch on Track 4 to " 4 ". The Track 4 REC SELECT indicator flashes. A signal output from the converter is routed to Track 4 via the MIC/LINE INPUT 4 of the MT400. 4 Set the [METER SELECT] switch to " 4TR ". 5 Press the [PAUSE] button, then the REC button. 6 Prepare the MIDI sequencer and FSK/MIDI or SMPTE/MIDI converter for SYNC signal output. 7 Start the MIDI sequencer, or SMPTE/MTC converter. A SYNC signal is sent from the converter to Track 4 via Input Channel 4. 8 While checking the level meter, use the GAIN control and the fader on Input Channel 4 to set the level of the SYNC signal. At this time, set all the EQ controls to midway around noon (flat). Note: If the level of the SYNC signal is too high, the signal may sometimes leak to an adjacent track. If the level is too low, you may not be able to achieve correct synchronization. Set the level so that the 0 dB segment of the level meter lights up. -Owner's Manual