Yamaha MT400 Owner's Manual - Page 34

33 Applying Effects at Mixdown One of the typical uses of external effects processors connected to AUX SENDs is to apply reverb effects to track signals during mixdown. In this case, you can adjust the amount of effects for each track individually using the AUX 1 and AUX 2 controls. 4 5 2 1 1 INSERT I/O MIC/LINE INPUT 2 INSERT I/O 3 STEREO INPUT 4 5L 6R 7L 8R AUX SEND 1 2 GAIN LINE HIGH -12 MID -12 LOW -12 AUX 1 0 AUX 2 0 MIX 1 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 2 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 3 GAIN MIC LINE HIGH +12 -12 MID +12 -12 LOW +12 -12 AUX 1 10 0 AUX 2 10 0 CUE MIX 4 5L-6R 7L-8R LEVEL LEVEL MIC 0 10 0 10 +12 MULTITRACK CASSETTE RECORDER +12 +6 +3 0 -5 -10 REC 1 2 3 4 L R +12 10 10 CUE TAPE SPEED CONTROL PITCH 4.8/ 9.5 - + ON OFF SYNC ZERO STOP ON OFF REC SELECT 1 2 3 4 OFF OFF OFF OFF L R L R +6 POWER +3 0 -5 -10 METER SELECT 4TR STEREO 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to L TAPE TAPE MIC/ LINE INPUT-FLIP 0 10 MIC/LINE to R TAPE TAPE MIC/ LINE INPUT-FLIP LEVEL PAN PAN PAN PAN MIN MONITOR/PHONES STEREO ST+CUE CUE MAX L R L R L R L R 10 10 10 10 9 9 9 9 8 8 8 8 7 7 7 7 6 6 6 6 5 5 5 5 4 4 4 4 3 3 3 3 2 2 2 2 1 1 1 1 0 0 0 0 STEREO 10 9 8 7 6 5 4 3 2 1 0 NOISE REDUCTION SYSTEM REC PLAY REW FF STOP PAUSE 6 3 1 Connect AUX SEND 1 to the input of an effects processor, and connect the outputs of the effects processor to STEREO INPUT 5L/6R. Set the effects processor so that it will output only the processed signal. 2 Set the [INPUT-FLIP] switches on Input Channels 1-4 to "TAPE ( )". Tracks 1-4 signals are sent to Input Channels 1-4. 3 Set the monitor select switch to "STEREO". 4 While playing the tape, use the faders, PAN controls and EQ controls on Input Channels 1-4 to adjust the volume balance, stereo image, and tonal quality of each track. 5 Turn up the AUX 1 control of the input channel to which you wish to apply effects. Channel signals (playback sound of Tracks 1-4) are sent to the effects processor connected to AUX SEND 1. Adjust the input level on the effects processor, if necessary. 6 Turn up the LEVEL control for STEREO INPUT 5L and 6R. The processed signal is returned from the effects processor and added to the Stereo bus of the MT400. The more you turn up the LEVEL control, the more effects you can obtain. -Owner's Manual