Yamaha MW10C MW8CX/MW10C Owners Manual - Page 25

Reference Specifications ■ Electrical Specifications Frequency Response Total Harmonic Distortion (THD + N) Hum & Noise Hum & Noise are measured with a 6 dB/ octave filter @12.7 kHz; equivalent to a 20 kHz filter with infinite dB/octave attenuation. Crosstalk (1 kHz) Maximum Voltage Gain (1 kHz) All level controls are maximum when measured PAN/BAL: panned hard left or hard right. Phantom Voltage STEREO OUT GAIN: min (CHs 1-5/6) EFFECT SEND 20 Hz-20 kHz (AUX SEND*) Nominal output level @1 kHz MONITOR OUT, REC OUT STEREO OUT +14 dBu, 20 Hz-20 kHz, Input Gain Control at minimum Input: CH INPUT 1, 2 MIC EIN (Equivalent Input Noise): Rs = 150 Ω, GAIN: maximum (CH1, 2) STEREO OUT STEREO Master control at nominal level and all CH Level control at minimum. EFFECT SEND All CH EFFECT (AUX*) controls at minimum. (AUX SEND*) STEREO OUT STEREO Master control and one CH level control at nominal level (CH1, 2) STEREO OUT Residual Output Noise Adjacent Input CH1, 2 Input to Output STEREO L/R, CH 1, 2, PAN: panned hard left or right Rs = 150 Ω MIC to CH INSERT OUT INPUT GAIN: maximum MIC to STEREO OUT MIC to REC OUT MIC to MONITOR OUT MIC to PHONES OUT MIC to EFFECT SEND (AUX SEND*) LINE to STEREO OUT LINE to EFFECT SEND (AUX SEND*) ST CH 7/8, (CHs 7/8, 9/10*) to STEREO OUT Rs = 150 Ω RETURN to STEREO OUT Rs = 600 Ω 2TR IN to STEREO OUT MIC no load MIN TYP MAX UNIT -3.0 1.0 -3.0 1.0 dB -3.0 1.0 0.1 % -128 -87 -85 dBu -64 -100 -70 dB -70 60 76 58.2 92 81 76 dB 50 47 26 12 23.8 48 V ■ General Specifications USB Audio Input HPF Input Equalization Turn over/roll-off frequency of shelving: 3 dB below maximum variable level. ±15 dB maximum PEAK Indicator Internal Digital Effect (Only MW8CX) LED Level Meter Power Supply Adaptor Power Consumption Dimensions (W x H x D) Net Weight Input/Output: 44.1/48 kHz CHs 1-5/6, 80 Hz, 12 dB/oct CHs 1-5/6 HIGH: 10 kHz (shelving) MID: 2.5 kHz (peaking) LOW: 100 Hz (shelving) CH 7/8 (CHs 7/8, 9/10*) HIGH: 10 kHz (shelving) LOW: 100 Hz (shelving) Red LED turns on when post EQ signal (either post MIC HA or post EQ signal for CHs 3/4, 5/6) reaches -3 dB below clipping (+17 dBu). 16 PROGRAM, PARAMETER control Foot Switch (Digital Effect On/Off) Pre MONITOR Level 2x7 points LED meter (PEAK, +6, +3, 0, -5, -10, -20 dB) PEAK lights if the signal level reaches 3 dB below the clipping level. PA-10 AC 38 VCT, 0.62 A, Cable Length = 3.6 m 21 W 256.6 mm x 62.2 mm x 302.5 mm 1.7 kg (MW8CX), 1.6 kg (MW10C) All level controls are nominal if not specified. Output impedance of signal generator: 150 ohms * The MW8CX feature is described first, followed by the MW10C feature in brackets: MW8CX (MW10C) MW8CX/MW10C Owner's Manual 91