Yamaha RX-V1400 Owner's Manual - Page 83

English, ADDITIONAL, INFORMATION, Dolby Digital or DTS

Get Yamaha RX-V1400 PDF manuals and user guides View all Yamaha RX-V1400 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 83 highlights

TROUBLESHOOTING Problem Cause Remedy Refer to page Dolby Digital or DTS The connected component is not set to Make an appropriate setting following the operations - sources cannot be output Dolby Digital or DTS digital instructions for your component. played. (Dolby Digital signals. or DTS indicator on the front panel INPUT MODE is set to ANALOG. Set INPUT MODE to AUTO or DTS. 34 display does not light up.) A "humming" sound Incorrect cable connections. can be heard. Firmly connect the audio plugs. If the problem - persists, the cables may be defective. No connection from the turntable to the Connect the grounding cord of your turnable to the 19 GND terminal. GND terminal of this unit. The volume level is The record is being played on a turntable The turntable should be connected to this unit through 19 low while playing a with an MC cartridge. an MC-head amplifier. record. The volume level The component connected to the OUT Turn on the power to the component. - cannot be increased, (REC) jacks of this unit is turned off. or the sound is distorted. The sound effect cannot be recorded. It is not possible to record the sound effect with a recording component. A source cannot be recorded by a digital recording component connected to this DIGITAL OUTPUT jack. The source component is not connected to this unit's DIGITAL INPUT jacks. Some components cannot record the Dolby Digital or DTS sources. Connect the source component to the DIGITAL INPUT jacks. 16-19 A source cannot be recorded by an analog component connected to the AUDIO OUT jacks. The source component is not connected to Connect the source component to the analog AUDIO 16-19 this unit's analog AUDIO IN jacks. IN jacks. The sound field "MEMORY GUARD" in the SET MENU Select OFF. 56 parameters and some is set to ON. other settings on this unit cannot be changed. This unit does not The internal microcomputer has been Disconnect the AC power cord from the outlet and - operate properly. frozen by an external electric shock (such then plug it in again after about 30 seconds. as lightning or excessive static electricity) or by a power supply with low voltage. "CHECK SP WIRES" appears on the front panel display. Speaker cables are short circuited. Make sure all speaker cables are connected correctly. 12 ADDITIONAL INFORMATION English 79

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
79
English
TROUBLESHOOTING
ADDITIONAL
INFORMATION
Problem
Cause
Remedy
Refer to
page
Dolby Digital or DTS
sources cannot be
played. (Dolby Digital
or DTS indicator on
the front panel
display does not light
up.)
The connected component is not set to
output Dolby Digital or DTS digital
signals.
Make an appropriate setting following the operations
instructions for your component.
—
INPUT MODE is set to ANALOG.
Set INPUT MODE to AUTO or DTS.
34
A “humming” sound
can be heard.
Incorrect cable connections.
Firmly connect the audio plugs. If the problem
persists, the cables may be defective.
—
No connection from the turntable to the
GND terminal.
Connect the grounding cord of your turnable to the
GND terminal of this unit.
19
The volume level is
low while playing a
record.
The record is being played on a turntable
with an MC cartridge.
The turntable should be connected to this unit through
an MC-head amplifier.
19
The volume level
cannot be increased,
or the sound is
distorted.
The component connected to the OUT
(REC) jacks of this unit is turned off.
Turn on the power to the component.
—
The sound effect
cannot be recorded.
It is not possible to record the sound effect
with a recording component.
A source cannot be
recorded by a digital
recording component
connected to this
DIGITAL OUTPUT
jack.
The source component is not connected to
this unit’s DIGITAL INPUT jacks.
Connect the source component to the DIGITAL
INPUT jacks.
16—19
Some components cannot record the
Dolby Digital or DTS sources.
A source cannot be
recorded by an
analog component
connected to the
AUDIO OUT jacks.
The source component is not connected to
this unit’s analog AUDIO IN jacks.
Connect the source component to the analog AUDIO
IN jacks.
16—19
The sound field
parameters and some
other settings on this
unit cannot be
changed.
“MEMORY GUARD” in the SET MENU
is set to ON.
Select OFF.
56
This unit does not
operate properly.
The internal microcomputer has been
frozen by an external electric shock (such
as lightning or excessive static electricity)
or by a power supply with low voltage.
Disconnect the AC power cord from the outlet and
then plug it in again after about 30 seconds.
—
“CHECK SP WIRES”
appears on the front
panel display.
Speaker cables are short circuited.
Make sure all speaker cables are connected correctly.
12