Yamaha RX-Z11 Owner's Manual - Page 17

Step 3: Turn on the power and start, playback, Are you enjoying playback? - troubleshooting

Get Yamaha RX-Z11 - AV Receiver PDF manuals and user guides
UPC - 027108929019
View all Yamaha RX-Z11 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

Introduction Step 3: Turn on the power and start playback Check the type of the connected speakers. If the speakers are 6-ohm speakers, set "SPEAKER IMP." to "6ΩMIN" before using this unit (see page 142). ■ After using this unit... Quick start guide Press AMAIN ZONE ON/OFF to set this unit to the standby mode. 1 Turn on the video monitor connected to this unit. 2 Press BMASTER ON/OFF on the front panel inward to the ON position. This unit is set to the standby mode and consumes a small amount of power in order to receive infrared signals from the remote control. To turn on this unit from the standby mode, press AMAIN ZONE ON/OFF on the front panel (or EPOWER on the remote control). See page 43 for details. Automatic setup feature To optimize the speaker settings for your listening room, use the automatic setup feature. See pages 47 to 52 for details. Note After this unit is turned on, it takes approximately 20 seconds until this unit produces sounds, and while "Please wait" appears in the front panel display, this unit does not accepts the front panel operations and stores the remote control operations. This unit performs the stored remote control operations after "Please wait" disappears. 3 Rotate the DINPUT selector to set the input source to "BD/HD DVD". y The recommended sound field program is set for each input source (BD/HD DVD, etc.). You can also use various sound field programs and other sound modes for playback. Refer to the following pages for details: - see pages 64 and 86 to use various sound field programs - see page 64 to turn on or off the sound effect - see page 65 to use the pure direct mode for high fidelity sound 4 Start playback of the desired Blu-ray Disc/HD DVD source on your player. 5 Rotate EVOLUME to adjust the volume. ■ Are you enjoying playback? If there are some troubles with playback, check the settings as follows. No sound is output. Are the speakers connected correctly? Â Check the speaker connection. Are Your Blu-ray Disc/HD DVD player connected correctly? Â Check the connection of the Blu-ray Disc/HD DVD player. Are the front speakers selected correctly? Â Press GSPEAKERS A or GSPEAKERS B. Is volume setting correct? Â Adjust the volume level. Does the Blu-ray Disc/HD DVD player play back correctly? Â Check the setting of the Blu-ray Disc/HD DVD player. No picture. Is the video monitor connected correctly? Â Check the connection of the video monitor. If the video monitor is connected to the HDMI OUT 1 jack of this unit, is the "HDMI OUT SEL" setting correct? Â Set the operation mode selector to CAMP and then press CHDMI OUT repeatedly to set "HDMI OUT SEL" to "OUT 1". Is Blu-ray Disc/HD DVD player connected correctly? Â Check the connection of the video monitor. Is the input source setting of the video monitor correct? Â Check the setting of the input source of the video monitor. Any other troubles? Refer to "Troubleshooting" on pages 146 to 153 for other troubles. 17 En

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
Quick start guide
17
En
Introduction
1
Turn on the video monitor connected to this unit.
2
Press
B
MASTER ON/OFF
on the front panel inward
to the ON position.
After this unit is turned on, it takes approximately 20 seconds until this
unit produces sounds, and while “Please wait” appears in the front
panel display, this unit does not accepts the front panel operations and
stores the remote control operations. This unit performs the stored
remote control operations after “Please wait” disappears.
3
Rotate the
D
INPUT
selector to set the input source
to “BD/HD DVD”.
y
The recommended sound field program is set for each input source
(BD/HD DVD, etc.). You can also use various sound field programs
and other sound modes for playback. Refer to the following pages for
details:
–
see pages 64 and 86 to use various sound field programs
–
see page 64 to turn on or off the sound effect
–
see page 65 to use the pure direct mode for high fidelity sound
4
Start playback of the desired Blu-ray Disc/HD DVD
source on your player.
5
Rotate
E
VOLUME
to adjust the volume.
■
After using this unit...
Press
A
MAIN ZONE ON/OFF
to set this unit to the
standby mode.
This unit is set to the standby mode and consumes a small amount
of power in order to receive infrared signals from the remote
control. To turn on this unit from the standby mode, press
A
MAIN
ZONE ON/OFF
on the front panel (or
E
POWER
on the remote
control). See page 43 for details.
■
Are you enjoying playback?
If there are some troubles with playback, check the settings as
follows.
No sound is output.
Are the speakers connected correctly?
Check the speaker connection.
Are Your Blu-ray Disc/HD DVD player connected correctly?
Check the connection of the Blu-ray Disc/HD DVD player.
Are the front speakers selected correctly?
Press
G
SPEAKERS A
or
G
SPEAKERS B
.
Is volume setting correct?
Adjust the volume level.
Does the Blu-ray Disc/HD DVD player play back correctly?
Check the setting of the Blu-ray Disc/HD DVD player.
No picture.
Is the video monitor connected correctly?
Check the connection of the video monitor.
If the video monitor is connected to the HDMI OUT 1 jack of
this unit, is the “HDMI OUT SEL” setting correct?
Set the operation mode selector to
C
AMP
and then press
C
HDMI OUT
repeatedly to set “HDMI OUT SEL” to
“OUT 1”.
Is Blu-ray Disc/HD DVD player connected correctly?
Check the connection of the video monitor.
Is the input source setting of the video monitor correct?
Check the setting of the input source of the video monitor.
Any other troubles?
Refer to “Troubleshooting” on pages 146 to 153 for other
troubles.
Step 3: Turn on the power and start
playback
Check the type of the connected speakers.
If the speakers are 6-ohm speakers, set “SPEAKER IMP.” to
“6
Ω
MIN” before using this unit (see page 142).
Note
Automatic setup feature
To optimize the speaker settings for your listening room, use the
automatic setup feature. See pages 47 to 52 for details.