Zanussi ZKN7147J Product Manaul - Page 22

local Service Centre.

Get Zanussi ZKN7147J PDF manuals and user guides View all Zanussi ZKN7147J manuals
Add to My Manuals
Save this manual to your list of manuals

Page 22 highlights

35° 45° • Screw the hose back to the machine and make sure the connection is tight. • Turn on the water tap. Frost precautions If the machine is installed in a place where the temperature could drop below 0°C, remove the remaining water from the inlet hose and the drain pump. 1. disconnect the mains plug from the mains socket. 2. close the water tap 3. unscrew the water inlet hose from the tap; 4. put the two ends of the inlet hose in a con- tainer and let the water flow out of the hose. 5. empty the drain pump as described in the 'Emergency emptying out' section. 6. when the drain pump is empty, install the water inlet hose again. Warning! What to do if... Make sure that the temperature is more than 0 °C before you use the appliance again. The manufacturer is not responsible for damages caused by low temperatures. Emergency emptying out If the appliance cannot drain the water, proceed as follows to empty out the machine: 1. pull out the plug from the power socket; 2. close the water tap; 3. if necessary, wait until the water has cooled down; 4. open the pump door; 5. place a container on the floor below the recess of the drain pump; 6. press the two levers and pull forward the drainage duct to let the water flow out; 7. when the container is full of water, put the drainage duct back again and empty the container; repeat this operation until water stops flowing out; 8. if necessary clean the pump (refer to the section 'Cleaning the pump' ); 9. close the drain pump door. When you drain the water with the emergency drain procedure, you must activate again the drain system: 1. Put 2 litres of water in the main wash compartment of the detergent dispenser. 2. Start the programme to drain the water. Certain problems are due to lack of simple maintenance or oversights, which can be solved easily without calling out an engineer. Before contacting your local Service Centre, please carry out the checks listed below. During machine operation it is possible that the red pilot light of button 7 blinks, one of the following alarm codes appears on the display and some acoustic signals sound every 20 seconds to indicate that the machine is not working: • : problem with the water supply. • : problem with the water draining. • : door open. Once the problem has been eliminated, press the button 7 to restart the programme. If after all checks, the problem persists, contact your local Service Centre. 22 www.zanussi.com

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
35°
45°
•
Screw the hose back to the machine and
make sure the connection is tight.
•
Turn on the water tap.
Frost precautions
If the machine is installed in a place where the
temperature could drop below 0°C, remove the
remaining water from the inlet hose and the
drain pump.
1.
disconnect the mains plug from the mains
socket.
2.
close the water tap
3.
unscrew the water inlet hose from the tap;
4.
put the two ends of the inlet hose in a con-
tainer and let the water flow out of the
hose.
5.
empty the drain pump as described in the
‘Emergency emptying out’ section.
6.
when the drain pump is empty, install the
water inlet hose again.
Warning!
Make sure that the temperature is more than 0
°C before you use the appliance again.
The manufacturer is not responsible for dam-
ages caused by low temperatures.
Emergency emptying out
If the appliance cannot drain the water, pro-
ceed as follows to empty out the machine:
1.
pull out the plug from the power socket;
2.
close the water tap;
3.
if necessary, wait until the water has
cooled down;
4.
open the pump door;
5.
place a container on the floor below the re-
cess of the drain pump;
6.
press the two levers and pull forward the
drainage duct to let the water flow out;
7.
when the container is full of water, put the
drainage duct back again and empty the
container;
repeat this operation until water stops
flowing out;
8.
if necessary clean the pump (refer to the
section ‘Cleaning the pump’ );
9.
close the drain pump door.
When you drain the water with the emergency
drain procedure, you must activate again the
drain system:
1.
Put 2 litres of water in the main wash com-
partment of the detergent dispenser.
2.
Start the programme to drain the water.
What to do if…
Certain problems are due to lack of simple
maintenance or oversights, which can be
solved easily without calling out an engineer.
Before contacting your local Service Centre,
please carry out the checks listed below.
During machine operation it is possible that the
red
pilot light of button
7
blinks, one of the fol-
lowing alarm codes appears on the display and
some acoustic signals sound every 20 seconds
to indicate that the machine is not working:
•
: problem with the water supply.
•
: problem with the water draining.
•
: door open.
Once the problem has been eliminated, press
the button
7
to restart the programme. If after
all checks, the problem persists, contact your
local Service Centre.
22
www.zanussi.com