Apple M8889LL/A User Guide - Page 32

rivet head.

Get Apple M8889LL/A - Xserve - 512 MB RAM PDF manuals and user guides
UPC - 718908456057
View all Apple M8889LL/A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

3 At the back of the server, position the small bracket inside the server's cover so that the head of one rivet is facing the side of the cover. Note: Start on the left side of the server (when facing the back). This makes installing the cable-management arm more efficient. 4 Push the rivet head through the hole that's near the back on the side of the cover. Install the brackets on the inside of the top cover. The forward rivet on each bracket must pass through the hole in the cover. Each bracket must be installed with the rivets oriented low on the bracket. The head of the rivet protrudes through the cover. 5 Position the long, U-shaped brace on the outside of the server's cover, so that the curved end is near the protruding rivet. The indented lip at the curved end of the brace should face the rivet head. 6 Slide the lip at the end of the brace over both rivets on the small bracket and continue to slide the brace forward a few inches. Slide the brace toward the front of the cover. Make sure that both rivets on the bracket have engaged the slot in the brace. Make sure the brace is on the outside of the cover and that both rivets are captured in the center opening of the brace. 32 Chapter 3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
32
Chapter
3
3
At the back of the server, position the small bracket inside the server’s cover so that the head
of one rivet is facing the side of the cover.
Note:
Start on the left side of the server (when facing the back). This makes installing the
cable-management arm more efficient.
4
Push the rivet head through the hole that’s near the back on the side of the cover.
The head of the rivet protrudes through the cover.
5
Position the long, U-shaped brace on the outside of the server’s cover, so that the curved end
is near the protruding rivet. The indented lip at the curved end of the brace should face the
rivet head.
6
Slide the lip at the end of the brace over both rivets on the small bracket and continue to
slide the brace forward a few inches.
Make sure the brace is on the outside of the cover and that both rivets are captured in the
center opening of the brace.
Install the brackets on
the inside of the top cover.
The forward rivet on each bracket
must pass through the hole in the cover.
Each bracket must be
installed with the rivets
oriented low on the bracket.
Slide the brace
toward the front of the cover.
Make sure that both rivets
on the bracket have engaged
the slot in the brace.