Apple M8889LL/A User Guide - Page 35

Insert the screw into its hole and tighten it so that the arm is fastened to the brace.

Get Apple M8889LL/A - Xserve - 512 MB RAM PDF manuals and user guides
UPC - 718908456057
View all Apple M8889LL/A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 35 highlights

2 Hold the cable-management arm with the long end closer to you and fold the hinged section of the long end away from you. The hinged section is the part from which you removed the clamp and screw. This section should be perpendicular to the main part of the arm, with the oval holes furthest from you. Mount the cable-management arm as close to the back of the server as possible. Rotate the mounting plate on the arm so that it lies against the inside of the U-shaped bracket. The U-shaped bracket should be sandwiched between the arm and the small clamp. Secure the clamp with the screw that held it stored on the arm. Screw Clamp Cable-management arm U-shaped bracket 3 Position the cable-management arm so that the hinged section is on the inside of the right brace, about 2 inches behind the server's back panel. 4 Hold the arm in place and put the clamp you detached on the opposite side of the arm, so that the screw hole in the center shows through the open part of the brace. 5 Insert the screw into its hole and tighten it so that the arm is fastened to the brace. 6 Thread the hook-and-loop straps through the holes in the cable-management arm. If the straps are already attached, skip this step. See "Connect Cables to the Server" on page 40 for details on connecting cables and using the cable-management arm. Installing Your Server in a Rack 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
Installing Your Server in a Rack
35
2
Hold the cable-management arm with the long end closer to you and fold the hinged section
of the long end away from you.
The hinged section is the part from which you removed the clamp and screw. This section
should be perpendicular to the main part of the arm, with the oval holes furthest from you.
3
Position the cable-management arm so that the hinged section is on the inside of the right
brace, about 2 inches behind the server’s back panel.
4
Hold the arm in place and put the clamp you detached on the opposite side of the arm, so
that the screw hole in the center shows through the open part of the brace.
5
Insert the screw into its hole and tighten it so that the arm is fastened to the brace.
6
Thread the hook-and-loop straps through the holes in the cable-management arm.
If the straps are already attached, skip this step.
See “Connect Cables to the Server” on page 40 for details on connecting cables and using the
cable-management arm.
Mount the cable-management arm as close to the back of
the server as possible. Rotate the mounting plate on the arm
so that it lies against the inside of the U-shaped bracket. The
U-shaped bracket should be sandwiched between the arm
and the small clamp. Secure the clamp with the screw that
held it stored on the arm.
Clamp
Screw
U-shaped bracket
Cable-management arm