Apple M8889LL/A User Guide - Page 52

Opening and Closing the Server

Get Apple M8889LL/A - Xserve - 512 MB RAM PDF manuals and user guides
UPC - 718908456057
View all Apple M8889LL/A manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

c Wait for the upper disk light to go off, then grasp the handle and pull the drive module out of its bay and set it aside. Pull the server drive module out of the server. 3 Press to open the handle of the replacement drive module and slide it into the empty bay until its connector clicks into place. 4 The disk status light turns green to indicate normal operation. Important Be sure to save the blank drive module if you removed one. This module should always be placed in an empty drive bay to maintain proper airflow through the server. Opening and Closing the Server 1 Shut down the server. Be sure to wait a brief period to allow the server's internal components to cool. Warning Always shut down your server before opening it to avoid damaging its internal components or the components you want to install. Do not open the server or attempt to install items inside it while it is turned on. After shutting down your server, the internal components can be very hot. Let the computer cool down before continuing. 2 If the cable-management arm is not in use for all cables, unplug all cables from the back panel except the power cord. (If necessary, also remove the FireWire cable from the front panel.) 52 Chapter 5

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
52
Chapter
5
c
Wait for the upper disk light to go off, then grasp the handle and pull the drive module
out of its bay and set it aside.
3
Press to open the handle of the replacement drive module and slide it into the empty bay
until its connector clicks into place.
4
The disk status light turns green to indicate normal operation.
Opening and Closing the Server
1
Shut down the server.
Be sure to wait a brief period to allow the server’s internal components to cool.
2
If the cable-management arm is not in use for all cables, unplug all cables from the back panel
except the power cord. (If necessary, also remove the FireWire cable from the front panel.)
Pull the server drive
module out of the server.
Important
Be sure to save the blank drive module if you removed one. This module should
always be placed in an empty drive bay to maintain proper airflow through the server.
Warning
Always shut down your server before opening it to avoid damaging its internal
components or the components you want to install. Do not open the server or attempt to
install items inside it while it is turned on. After shutting down your server, the internal
components can be very hot. Let the computer cool down before continuing.