Asus P4PE-BP Motherboard DIY Troubleshooting Guide - Page 28

Connectors

Get Asus P4PE-BP PDF manuals and user guides View all Asus P4PE-BP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

1.12 Connectors This section describes and illustrates the internal connectors on the motherboard. 1. Hard disk activity LED (2-pin IDE_LED1) This connector supplies power to the hard disk activity LED. The read or write activities of any device connected to the primary or secondary IDE connector cause this LED to light up. P4PE BP TIP: If the case-mounted LED does not ® light up, try reversing the 2-pin plug. IDE_LED1 P4PE BP HD Activity LED 2. Floppy disk drive connector (34-1 pin FLOPPY) This connector supports the provided floppy drive ribbon cable. After connecting one end to the motherboard, connect the other end to the floppy drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables with pin 5 plug). FLOPPY1 ® P4PE BP NOTE: Orient the red markings on the floppy ribbon cable to PIN 1. PIN 1 P4PE BP Floppy Disk Drive Connector 1-18 Chapter 1: Product introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
1-18
Chapter 1: Product introduction
1.12
Connectors
This section describes and illustrates the internal connectors on the motherboard.
1.
Hard disk activity LED (2-pin IDE_LED1)
This connector supplies power to the hard disk activity LED. The read or write
activities of any device connected to the primary or secondary IDE connector
cause this LED to light up.
2.
Floppy disk drive connector (34-1 pin FLOPPY)
This connector supports the provided floppy drive ribbon cable. After
connecting one end to the motherboard, connect the other end to the floppy
drive. (Pin 5 is removed to prevent incorrect insertion when using ribbon cables
with pin 5 plug).
P4PE BP
P4PE BP HD Activity LED
TIP:
If the case-mounted LED does not
light up, try reversing the 2-pin plug.
IDE_LED1
P4PE BP
NOTE:
Orient the red markings on
the floppy ribbon cable to PIN 1.
P4PE BP Floppy Disk Drive Connector
PIN 1
FLOPPY1