Asus P4PE-BP Motherboard DIY Troubleshooting Guide - Page 29

IDE connectors 40-1 pin PRI_IDE, SEC_IDE, Power supply thermal connector 2-pin TRPWR1

Get Asus P4PE-BP PDF manuals and user guides View all Asus P4PE-BP manuals
Add to My Manuals
Save this manual to your list of manuals

Page 29 highlights

3. IDE connectors (40-1 pin PRI_IDE, SEC_IDE) This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon cable. Connect the cable's blue connector to the primary (recommended) or secondary IDE connector, then connect the gray connector to the UltraDMA/100/66 slave device (hard disk drive) and the black connector to the UltraDMA/100/66 master device. It is recommended that you connect nonUltraDMA/100/66 devices to the secondary IDE connector. If you install two hard disks, you must configure the second drive as a slave device by setting its jumper accordingly. Refer to the hard disk documentation for the jumper settings. BIOS supports specific device bootup. If you have more than two UltraDMA/100/66 devices, purchase another UltraDMA/100/66 cable. You may configure two hard disks to be both master devices with two ribbon cables - one for the primary IDE connector and another for the secondary IDE connector. 1. Pin 20 on each IDE connector is removed to match the covered hole on the UltraDMA cable connector. This prevents incorrect orientation when you connect the cables. 2. The hole near the blue connector on the UltraDMA/100/66 cable is intentional. ® P4PE BP NOTE: Orient the red markings (usually zigzag) on the IDE ribbon cable to PIN 1. SEC_IDE PRI_IDE P4PE BP IDE Connectors PIN 1 PIN 1 10. Power supply thermal connector (2-pin TRPWR1) If your power supply has a thermal monitoring feature, connect its thermal sensor cable to this connector. ® P4PE BP TRPWR1 Ground TRPWR P4PE BP Power Supply Thermal Connector ASUS P4PE BP motherboard user guide 1-19

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
ASUS P4PE BP motherboard user guide
1-19
3.
IDE connectors (40-1 pin PRI_IDE, SEC_IDE)
This connector supports the provided UltraDMA/100/66 IDE hard disk ribbon
cable. Connect the cable’s blue connector to the primary (recommended) or
secondary IDE connector, then connect the gray connector to the
UltraDMA/100/66 slave device (hard disk drive) and the black connector to the
UltraDMA/100/66 master device. It is recommended that you connect non-
UltraDMA/100/66 devices to the secondary IDE connector. If you install two hard
disks, you must configure the second drive as a slave device by setting its
jumper accordingly. Refer to the hard disk documentation for the jumper settings.
BIOS supports specific device bootup.
If you have more than two
UltraDMA/100/66 devices, purchase another UltraDMA/100/66 cable. You may
configure two hard disks to be both master devices with two ribbon cables – one
for the primary IDE connector and another for the secondary IDE connector.
1.
Pin 20 on each IDE connector is removed to match the covered hole on the
UltraDMA cable connector. This prevents incorrect orientation when you
connect the cables.
2.
The hole near the blue connector on the UltraDMA/100/66 cable is intentional.
P4PE BP
P4PE BP IDE Connectors
NOTE:
Orient the red markings
(usually zigzag) on the IDE
ribbon cable to PIN 1.
SEC_IDE
PIN 1
PIN 1
PRI_IDE
P4PE BP
P4PE BP Power Supply Thermal Connector
TRPWR1
Ground
TRPWR
10. Power supply thermal connector (2-pin TRPWR1)
If your power supply has a thermal monitoring feature, connect its thermal
sensor cable to this connector.