BenQ RM8602K RS232 & LAN Command List

BenQ RM8602K Manual

Get BenQ RM8602K PDF manuals and user guides View all BenQ RM8602K manuals
Add to My Manuals
Save this manual to your list of manuals

BenQ RM8602K manual content summary:

  • BenQ RM8602K | RS232 & LAN Command List - Page 1
    RM5502K/RM6502K/RM7502K/RM8602K RS232 & LAN Protocol Installation Guide 1
  • BenQ RM8602K | RS232 & LAN Command List - Page 2
    Table of Contents Introduction ...2 Wire arrangement ...3 RS232 pin assignment ...3 Communication setting ...4 Command message reference...4 Connections and communication settings 4 RS232 serial port connection...4 RS232 via LAN...5 RS232 via HDBaseT ...5 Protocol Command Description 5 Set-
  • BenQ RM8602K | RS232 & LAN Command List - Page 3
    Introduction This document describes the hardware interface spec and software protocols of RS232 interface communication between Commercial Display and PC or other control unit with RS232 protocol. This set protocol allows users to assign the ID in the command to control the specify ID monitor. The
  • BenQ RM8602K | RS232 & LAN Command List - Page 4
    Communication setting Baud rate select: 9600bps (fixed)/ Data bits: 8 bits (fixed) Parity: None (fixed)/ Stop Bits: 1(fixed) Command message reference PC sends to Monitor command packet followed by "CR". Every time PC sends control command to the Monitor, the Monitor shall response as follows: 1. If
  • BenQ RM8602K | RS232 & LAN Command List - Page 5
    RS232 via LAN RJ45 port on a display PC or laptop LAN cable Find the Wired LAN IP address of the connected display from the OSD menu and make sure the display and the computer are within the same network. IP Protocol Port: 4660 RS232 via HDBaseT HDBaseT compatible device RJ45 port on a
  • BenQ RM8602K | RS232 & LAN Command List - Page 6
    Value [1~3] CR Three bytes ASCII that defines the value 0x0D Set-function listing The PC can control the LCD Monitor for specific actions. The Set-Function command allows you to control the LCD monitor behavior in a remote sit through the RS232 port. The Set-Function packet format consists of 11
  • BenQ RM8602K | RS232 & LAN Command List - Page 7
    Example 2: Set Brightness as 176 and this command is NOT valid. Send (Hex Format) Name Length ID Command type Command Hex 0x38 0x30 0x31 0x73 0x24 Value1 0x31 Value2 0x37 Value3 0x36 CR 0x0D Reply (Hex Format) Name Length Hex 0x34 ID 0x30 0x31 Command type 0x2D CR 0x0D Example
  • BenQ RM8602K | RS232 & LAN Command List - Page 8
    Set-function table Set Function Len Power 8 Video Source 8 Contrast 8 Brightness 8 Sharpness 8 Aspect Ratio 8 Language 8 Cmd Code ID Cmd Type RS232 (ASCII Bytes) (Hex) 001 : On s 21 002 : Standby (or android off) 003 : Reboot 000 : VGA 001 : HDMI1 002: HDMI2 s 22 021 :
  • BenQ RM8602K | RS232 & LAN Command List - Page 9
    Sound Mode 8 Volume 8 Mute 8 Treble 8 Bass 8 Balance 8 Remote control 8 command IR Control 8 Button&IR 8 Control Button 8 Control Pixel Shift 8 Picture Mode 8 019:Arabic 019:Arabic 020:Japanse 020:Japanse 021: Thailand 021: Thailand 022: Korean 022: Korean 023 :
  • BenQ RM8602K | RS232 & LAN Command List - Page 10
    Chroma 8 (Color) Backlight 8 DCR 8 Color Temp 8 Auto Adjustment 8 Execute EyeCare 8 Option RTC Year 8 RTC Month 8 RTC Day 8 RTC Hour 8 RTC Minute 8 Touch 8 Feature Power Save 8 Switch on 8 Status s 82 000 ~ 050 s 84 000 ~ 100 000: Off s 85 001: On 000 : Cool s 86 001 :
  • BenQ RM8602K | RS232 & LAN Command List - Page 11
    On/Off Timer 14 WOL 8 Byte1~Byte9 (1) Byte1: Decide which Timer is Byte1~Byte9 selected, and its enable/disable (1) Byte1: Decide which Timer is setting. selected, and its enable/disable Byte1[3:0]=0x1~0x07. There are setting. totally 7 Timers, this value is used Byte1[3:0]=0x1~0x07. There
  • BenQ RM8602K | RS232 & LAN Command List - Page 12
    EyeCare 8 000: Off s F3 001: On 000: Off 001: On 12
  • BenQ RM8602K | RS232 & LAN Command List - Page 13
    Get-function listing The PC can interrogate the LCD Monitor for specific information. The Get-Function packet format consists of 5 bytes which are similar to the Set-Function packet structure. Note that the "Value" byte is always = 00. Get-function description Item Length TV ID Command Type
  • BenQ RM8602K | RS232 & LAN Command List - Page 14
    Example 1: Get Brightness and this command is valid. The Brightness value is 67. Send (Hex Format) Name Length ID Command type Hex 0x38 0x30 0x31 0x67 Reply (Hex Format) Name Length Hex 0x38 ID 0x30 0x31 Command type 0x72 Command 0x62 Value1 0x30 Value2 0x30 Value3 0x30 Command
  • BenQ RM8602K | RS232 & LAN Command List - Page 15
    Example 6: Get CO2 Value from System and this command is valid. The lux value is 786 (ASCII code). Send (Hex Format) Name Length ID Command type Command Value1 Value2 Value3 Value4 Value5 CR Hex 0x38 0x30 0x31 0x67 0XAB 0x30 0x30 0x30 0x30 0x30 0x0D Reply (Hex Format) Name Length ID Hex
  • BenQ RM8602K | RS232 & LAN Command List - Page 16
    PC Get-function command to IFP Get Function Len Cmd Cmd ID Code RS232 LAN Type (Hex) (1) Input value: Byte1 - Byte2 - (1) Input value: Byte1 - Byte2 - Byte3...Byte15 Byte3...Byte15 Byte2~Byte11=0x00 Byte2~Byte11=0x00 Byte1=0x01: Get Customer Name Byte1=0x01: Get Customer Name Byte1=
  • BenQ RM8602K | RS232 & LAN Command List - Page 17
    Volume 8 Mute 8 IR Control 8 Button&IR 8 Control Video Source 8 Power 8 Pixel Shift 8 Button 8 Control Operation 10 Time Aspect Ratio 8 Language 8 003 : Class 004 : Meeting g 66 000 ~ 100 000: Off g 67 001: On 000: Disable g 68 001: Enable 000: Disable g 69 001: Enable 000 : VGA 001 :
  • BenQ RM8602K | RS232 & LAN Command List - Page 18
    015:Norwegian 016:Finnish 017:Greek 018:Turkish 019:Arabic 020:Japanse 021: Thailand 022: Korean 023 : Hungarian 024 : Persian 025 : Vietnamese Touch 8 Feature 000: Off g 9E 001: On 000: Standard Picture Mode 8 g B1 001: Bright 002 : Soft Chroma 8 (Color) g B2 000 ~ 050 Backlight
  • BenQ RM8602K | RS232 & LAN Command List - Page 19
    On/Off Timer 14 Input value: Byte1 - Byte2 - Byte3...Byte9 Input value: Byte1 - Byte2 - Byte3...Byte9 (1) Byte1[3:0]: The Number of the (1) Byte1[3:0]: The Number of the On/Off Timer. There are totally 7 On/Off On/Off Timer. There are totally 7 On/Off Timers, and this byte is used to selected
  • BenQ RM8602K | RS232 & LAN Command List - Page 20
    reserved. reserved. (8) Byte8~9 are reserved, and should be (8) Byte8~9 are reserved, and should be 0x00. 0x00. Network 14 Setting Input Value: Byte1 - Byte2 - Byte3...Byte9 Input Value: Byte1 - Byte2 - Byte3...Byte9 (1) Byte1=0x00: IP Setup Mode (1) Byte1=0x00: IP Setup Mode Byte1=0x01: IP
  • BenQ RM8602K | RS232 & LAN Command List - Page 21
    Input value, the return value should be 0x01: DHCP Byte1=0x00 Byte3~9 are reserved, should be Byte2=0x00: Manual 0x00. 0x01: DHCP (2) If Byte1=0x01(IP Address) at Input Byte3~9 are reserved, should be value, the return value should be 0x00. Ex: IP address=
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
1
RM5502K/RM6502K/RM7502K/RM8602K
RS232 & LAN Protocol
Installation Guide