Bosch SGE53C52UC Use and Care Manuals - Page 46

Setting the amount of rinse aid, Adding rinse aid, Loading dishware,

Page 46 highlights

en-us Troubleshooting Issue Cause and troubleshooting There are remov- Amount of rinse aid to be dispensed is set too able streaks on high. glasses, glassware ▶ Set the rinse aid system to a lower setting. with a metallic ap- → "Setting the amount of rinse aid", Page 22 pearance and silverware. No rinse aid has been added. ▶ Add rinse aid. → "Adding rinse aid", Page 21 There is detergent residue in the final rinse. Lid of detergent dispenser is blocked by dishware and will not open fully. 1. Arrange dishware in the upper rack so the tab collecting tray is not obstructed by dishware. → "Loading dishware", Page 25 Items of dishware are blocking the dispenser lid. 2. Do not place dishware or fragrance dispensers in the tab collecting tray. Dishware has been precleaned too intensively. Then the sensors choose a lighter cycle. Stubborn remnants cannot be entirely removed. ▶ Only remove large remnants of food and do not pre-rinse dishware. Irreversible clouding Glasses are not dishwasher-proof, only suitable of glassware. for dishwashers. ▶ Use dishwasher-proof glasses. Glasses are usually only suitable for cleaning in a dishwasher, i.e. long-term wear or longterm changes must be expected. ▶ Avoid a lengthy steam phase (standing time after wash cycle ends). ▶ Use a program with a lower temperature. ▶ Set the softening system to the water hardness. → "Setting the water softening system", Page 20 ▶ Use detergent with a glass protection component. Detergent residue is Spray arms were blocked by dishware so deter- present in the deter- gent was not rinsed out. gent dispenser or ▶ Check that the spray arms are not blocked and the tab collecting can rotate freely. tray. Detergent dispenser was damp when detergent was added. 46

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60

en-us
Troubleshooting
46
Issue
Cause and troubleshooting
There are remov-
able streaks on
glasses, glassware
with a metallic ap-
pearance and silver-
ware.
Amount of rinse aid to be dispensed is set too
high.
Set the rinse aid system to a lower setting.
"Setting the amount of rinse aid", Page 22
No rinse aid has been added.
Add rinse aid.
"Adding rinse aid", Page 21
There is detergent residue in the final rinse. Lid of
detergent dispenser is blocked by dishware and
will not open fully.
1.
Arrange dishware in the upper rack so the tab
collecting tray is not obstructed by dishware.
"Loading dishware", Page 25
Items of dishware are blocking the dispenser
lid.
2.
Do not place dishware or fragrance dispensers
in the tab collecting tray.
Dishware has been precleaned too intensively.
Then the sensors choose a lighter cycle. Stub-
born remnants cannot be entirely removed.
Only remove large remnants of food and do not
pre-rinse dishware.
Irreversible clouding
of glassware.
Glasses are not dishwasher-proof, only suitable
for dishwashers.
Use dishwasher-proof glasses.
Glasses are usually only suitable for cleaning
in a dishwasher, i.e. long-term wear or long-
term changes must be expected.
Avoid a lengthy steam phase (standing time af-
ter wash cycle ends).
Use a program with a lower temperature.
Set the softening system to the water hard-
ness.
"Setting the water softening system",
Page 20
Use detergent with a glass protection compo-
nent.
Detergent residue is
present in the deter-
gent dispenser or
the tab collecting
tray.
Spray arms were blocked by dishware so deter-
gent was not rinsed out.
Check that the spray arms are not blocked and
can rotate freely.
Detergent dispenser was damp when detergent
was added.