Bosch SGE53C52UC Use and Care Manuals - Page 48

Issue, Cause and troubleshooting, Reset

Get Bosch SGE53C52UC PDF manuals and user guides View all Bosch SGE53C52UC manuals
Add to My Manuals
Save this manual to your list of manuals

Page 48 highlights

en-us Troubleshooting Issue Display flashes. Cause and troubleshooting Appliance door is not closed properly. ▶ Close the appliance door. ‒ Arrange the dishware so that no parts project beyond the rack and prevent the appliance door from closing properly. All LEDs light up or flash. Electronics have detected a fault. 1. Press the main switch button for approx. 4 sec- onds. → "Controls", Page 11 The appliance is reset and restarted. 2. If the problem occurs again: ‒ Switch off the appliance. ‒ Unplug the power plug or switch off the cir- cuit breaker in the fuse box. ‒ Wait at least 2 minutes. ‒ Switch on the circuit breaker in the fuse box or plug in the power plug. ‒ Switch on the appliance. 3. If the problem occurs again: ‒ Contact customer service. → "Customer Service", Page 52 UP appears on the display. A software update is available. ▶ Press the remote start button to install the soft- ware update. a After a successful software update, "Suc" appears on the display for a few seconds. Water is left in the Filter system or area under the filters is blocked. appliance at the end 1. Clean the Filters → Page 36. of the program. 2. Clean the Drain pump → Page 50. Program has not yet ended. ▶ Wait until the program ends or terminate the program with Reset. ▶ → "Terminating the wash cycle", Page 29 Appliance cannot be Software update is taking place. switched on or oper- ▶ Wait until the software update has finished. ated. Appliance functions have failed. 1. Pull out the power cord plug or switch off the breaker. 2. Wait at least 2 minutes. 3. Connect the appliance to the power supply. 4. Switch the appliance on. 48

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
en-us
Troubleshooting
48
Issue
Cause and troubleshooting
Display flashes.
Appliance door is not closed properly.
▶
Close the appliance door.
‒
Arrange the dishware so that no parts
project beyond the rack and prevent the ap-
pliance door from closing properly.
All LEDs light up or
flash.
Electronics have detected a fault.
1.
Press the main switch button for approx. 4 sec-
onds.
→
"Controls", Page 11
The appliance is reset and restarted.
2.
If the problem occurs again:
‒
Switch off the appliance.
‒
Unplug the power plug or switch off the cir-
cuit breaker in the fuse box.
‒
Wait at least 2 minutes.
‒
Switch on the circuit breaker in the fuse box
or plug in the power plug.
‒
Switch on the appliance.
3.
If the problem occurs again:
‒
Contact customer service.
→
"Customer Service", Page 52
UP appears on the
display.
A software update is available.
▶
Press the remote start button to install the soft-
ware update.
a
After a successful software update, "Suc" ap-
pears on the display for a few seconds.
Water is left in the
appliance at the end
of the program.
Filter system or area under the filters is blocked.
1.
Clean the Filters
→
Page 36
.
2.
Clean the Drain pump
→
Page 50
.
Program has not yet ended.
▶
Wait until the program ends or terminate the
program with
Reset
.
▶
→
"Terminating the wash cycle", Page 29
Appliance cannot be
switched on or oper-
ated.
Software update is taking place.
▶
Wait until the software update has finished.
Appliance functions have failed.
1.
Pull out the power cord plug or switch off the
breaker.
2.
Wait at least 2 minutes.
3.
Connect the appliance to the power supply.
4.
Switch the appliance on.