Home » Brother International Manuals » Label Makers » Brother International PT-P900 » Manual Viewer

Brother International PT-P900 P-touch Template Manual/ Command Reference - Page 32

Others, 4.6.1 Transferring templates, 4.6.2 About objects in a template

View all Brother International PT-P900 manuals

Add to My Manuals
Save this manual to your list of manuals

Page 32 highlights

P-touch Template Command Reference 4.6 Others 4.6.1 Transferring templates  A maximum of 99 templates can be transferred. The transfer cannot be completed if the amount of data being transferred exceeds 7MByte.  A single template can contain a maximum of 50 objects. When trying to transfer more than 50 objects, an error will occur and the transfer cannot be completed.  When print data is fed, the command mode should be the P-touch Template mode.  When a template is transferred to the printer, all values specified with dynamic commands are initialized.  This is not compatible with split labels.  After printing from P-touch Editor, the command mode changes to raster mode. In order to print a template, select the P-touch Template mode in the P-touch Template Settings tool or, if the previous mode in the P-touch Template Settings tool was the P-touch Template mode, turn the printer off, then on again to enter P-touch Template mode. 4.6.2 About objects in a template  The line feed codes (0D0A, 0D and 0A) in print data are read, then discarded. However, when specified as special data, such as delimiters, print start text strings or line feed commands, they are applied.  The order of the objects is determined only by the last four-digit number of the object name. Objects with no numbers in their names will be at the end of the order. If objects have the same number, the order is determined in the following order: text, 1D barcodes, then 2D barcodes. If the objects are of the same type, the object created first is first in the order. We recommend that the numbers indicating the order be added at the end of the object name. (To specify the name of an object in P-touch Editor, display the properties of the text or barcode object, and then specify the name in the "Object Name" box on the Expanded tab.) Specifying the object name - 26 - 4. P-touch Template Limitations

Section	Page
P-touch Template Command ReferencePT-P900W/P950NW	1
IMPORTANT - PLEASE READ CAREFULLY	3
Note	3
Condition of Use	3
No Warranty	3
Contents	4
Introduction	7
What is P-touch Template?	8
1. Using P-touch Template	9
2. P-touch Template Settings Tool User’s Guide	10
3. Examples for Using Commands	16
3.1 Example for using P-touch Template	16
3.2 Example for printing logo/external characters in P-touch Template	20
4. P-touch Template　Limitations	24
4.1 Relating to text objects	24
4.1.1 Font, size, etc.	24
4.1.2 Character alignment	26
4.1.3 Text Layout settings	27
4.2 Relating to barcodes	28
4.2.1 Barcodes	28
4.2.2 1D barcodes	29
4.2.3 2D barcodes	30
4.3 Relating to images	31
4.4 Relating to Numbering	31
4.5 Relating to Database	31
4.6 Others	32
4.6.1 Transferring templates	32
4.6.2 About objects in a template	32
5. Precautions	33
5.1 Notes for printers with Bluetooth interface	33
5.2 Relationship between the P-touch Editor settings and the printer image	34
5.3 Making a template in order to save time before starting to print	35
6. Control Code Lists	36
6.1 Setting and retrieving commands for P-touch Template mode	36
6.2 Setting and retrieving commands for raster mode	38
7. Control Command Details	40
^PT Select print start trigger	40
^FF Start printing	41
^PS Specify print start command text string	42
^PC Specify print start received character count	43
^SS Specify delimiter	44
^TS Select template	45
^LS Specify line spacing with line feed	46
^CC Change the prefix character	47
^RC Specify line feed command text string	48
^CN Specify number of copies	49
^NN Specify number of Numbering copies	50
^ID Initialize template data	51
^QS Select print options	52
^QV Specify QR Code version	53
^FC FNC1 replacement setting	54
^CF Full cut setting	55
^CH Half cut setting	56
^CP Chain printing setting	57
^MP Mirror printing setting	58
^II Initialize	59
^OP Perform machine operations (feed/cut)	60
^SR Status request	61
^VR Retrieve version information	67
^CR Line feed in object	68
^OS Select object (object number)	69
^ON Select object (object name)	70
^DI Directly insert object	71
ESC i a Specify command mode	72
ESC iXT2 Select print start trigger	73
ESC iXP2 Specify print start command text string	74
ESC iXr2 Specify print start received character count	75
ESC iXD2 Specify delimiter	76
ESC iXa2 Specify non-printed text strings	77
ESC iXi2 Specify command mode	78
ESC iXn2 Select template	79
ESC iXf2 Change the prefix character	80
ESC iXc2 Select printer settings (cut options)	81
ESC iXy2 Select printer settings (cut options–specifying number of labels)	82
ESC iXH2 Half cut setting	83
ESC iXM2 Mirror printing setting	84
ESC iXs2 Special tape setting	85
ESC iXm2 Select character code set	86
ESC iXj2 Select international character set	87
ESC iXR2 Specify line feed command text string	88
ESC iXC2 Specify number of copies	89
ESC iXN2 Specify number of Numbering copies	90
ESC iXF2 FNC1 replacement setting	91
ESC iXq2 Select print options	92
ESC iXT1 Retrieve select print start trigger items	93
ESC iXP1 Retrieve print start command setting text string	94
ESC iXr1 Retrieve print start received character count	95
ESC iXD1 Retrieve delimiter	96
ESC iXa1 Retrieve non-printed text strings	97
ESC iXi1 Retrieve command mode setting	98
ESC iXn1 Retrieve template selection number	99
ESC iXc1 Retrieve printer settings (cut options)	100
ESC iXy1 Retrieve printer settings (cut options–specifying number of labels)	101
ESC iXH1 Retrieve half cut setting	102
ESC iXM1 Retrieve mirror printing setting	103
ESC iXs1 Retrieve special tape setting	104
ESC iXm1 Retrieve character code set setting	105
ESC iXj1 Retrieve international character set setting	106
ESC iXf1 Retrieve the prefix character	107
ESC iXR1 Retrieve line feed command setting text string	108
ESC iXC1 Retrieve number of copies setting	109
ESC iXN1 Retrieve number of Numbering copies setting	110
ESC iXF1 Retrieve FNC1 replacement setting	111
ESC iXq1 Retrieve print options	112
Appendix A: Specifications	113
Appendix B: Character Code Tables	114
International character set table	117
Appendix C: Troubleshooting	118
If printing does not begin (main most frequent cause)	118
If a template linked to a database is not printed	118
Appendix D: Introducing the Brother Developer Center	119

Match case Limit results 1 per page

P-touch Template Command Reference

- 26 -

P-touch Template

Limitations

4.6 Others

4.6.1 Transferring templates



A maximum of 99 templates can be transferred. The transfer cannot be completed if the amount of data

being transferred exceeds 7MByte.



A single template can contain a maximum of 50 objects. When trying to transfer more than 50 objects, an

error will occur and the transfer cannot be completed.



When print data is fed, the command mode should be the P-touch Template mode.



When a template is transferred to the printer, all values specified with dynamic commands are initialized.



This is not compatible with split labels.



After printing from P-touch Editor, the command mode changes to raster mode. In order to print a template,

select the P-touch Template mode in the P-touch Template Settings tool or, if the previous mode in the

P-touch Template Settings tool was the P-touch Template mode, turn the printer off, then on again to enter

P-touch Template mode.

4.6.2 About objects in a template



The line feed codes (0D0A, 0D and 0A) in print data are read, then discarded. However, when specified as

special data, such as delimiters, print start text strings or line feed commands, they are applied.



The order of the objects is determined only by the last four-digit number of the object name. Objects with

no numbers in their names will be at the end of the order. If objects have the same number, the order is

determined in the following order: text, 1D barcodes, then 2D barcodes. If the objects are of the same type,

the object created first is first in the order. We recommend that the numbers indicating the order be added

at the end of the object name.

(To specify the name of an object in P-touch Editor, display the properties of the text or barcode object, and

then specify the name in the “Object Name” box on the Expanded tab.)

Specifying the object name