Canon imagePROGRAF GP-300 imagePROGRAF GP-300 / GP-200 Setup Guide - Page 9

Installing the Print Head

Get Canon imagePROGRAF GP-300 PDF manuals and user guides View all Canon imagePROGRAF GP-300 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 9 highlights

6 Installing the Print Head Instructions are now shown on the touch screen regarding print head installation. Install the print head by following the instructions. 1 Open the top cover. 2 Tilt the print head lock lever towards you. Important ● Do not move the carriage (the area enclosed by a circle in the diagram). If you accidentally move it, temporarily close the top cover and it will return to its original position. 3 Open the print head locking cover and tap OK on the touch screen. At this time, check that there is no dirt on the electrical contacts of the carriage. 4 Grasp the print head as shown in the diagram and remove it from the bag. Hold here Contacts on the carriage 5 Remove the orange protective caps in the order shown in the diagram. Hold here to remove 6 Install the print head. ● Align the print head so that the area enclosed by a circle in the diagram is facing you, and carefully push the print head firmly into the printer, ensuring that the part covered by the protective caps does not touch the carriage. Important ● Do not touch the part that was being protected by the protective cap (part shown shaded in the diagram) under any circumstances. Touching it may cause damage to the print head or printing problems. ● The print head is filled with ink. Be careful to avoid getting your clothes and surrounding items dirty when removing the protective caps. It is recommended that you remove the protective caps above the bag that contained the print head. ● Do not reattach the protective caps after removing them. Furthermore, dispose of them according to local regulations. 8

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
8
6
Installing the Print Head
Instructions are now shown on the touch screen regarding print head installation. Install the print head by following the instructions.
1
Open the top cover.
Important
●
Do not move the carriage (the area enclosed by a circle in the
diagram). If you accidentally move it, temporarily close the top
cover and it will return to its original position.
2
Tilt the print head lock lever towards you.
3
Open the print head locking cover and tap
OK
on the
touch screen. At this time, check that there is no dirt on
the electrical contacts of the carriage.
Contacts on the carriage
4
Grasp the print head as shown in the diagram and
remove it from the bag.
Hold here
5
Remove the orange protective caps in the order shown in
the diagram.
Hold here to
remove
Important
●
Do not touch the part that was being
protected by the protective cap (part
shown shaded in the diagram) under any
circumstances. Touching it may cause
damage to the print head or printing
problems.
●
The print head is filled with ink. Be careful to
avoid getting your clothes and surrounding
items dirty when removing the protective
caps. It is recommended that you remove
the protective caps above the bag that
contained the print head.
●
Do not reattach the protective caps after
removing them. Furthermore, dispose of
them according to local regulations.
6
Install the print head.
●
Align the print head so that the area enclosed by a circle in the
diagram is facing you, and carefully push the print head firmly
into the printer, ensuring that the part covered by the protective
caps does not touch the carriage.