Cisco SR224 User Guide - Page 26

System Tab, Advanced Switch Configuration - default ip

Get Cisco SR224 - Small Business Unmanaged Switch PDF manuals and user guides
UPC - 745883556526
View all Cisco SR224 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

24-port 10/100 + 2-Port Gigabit Switch with WebView System Tab The System tab displays the system information. • Firmware version. The current firmware version is displayed. • MAC Address. The MAC Address of the Switch is displayed. • IP Address. This IP Address of the network is displayed. (The default IP address is 192.168.1.254. Verify the address. You can change the IP address, subnet mask, and default gateway here. • Subnet Mask. The subnet mask of the network is displayed. • Default Gateway. The default gateway of the network is displayed. Click the Apply button after you have verified that the information is correct. These following links are available on this tab: To configure the advanced switch configuration, click the Click here to configure MISC configuration link. To configure your username and password, click the Click here to configure your Username/Password link. (Figure 5-6) To reboot your system, click the Click here to reboot system link. To restore the Switch back to the default settings, click the Click here to restore system default setting link. Figure 5-4: System Tab-System Information Advanced Switch Configuration (Figure 5-5.) This screen allows you to make advanced switch configuration settings. Broadcast Storm Filter. This allows you to filter by percentage the amount of broadcast traffic to your network to prevent a storm of too many broadcasts from being sent at the same time. Select 5%, 10%, or 20% from the drop-down menu. Select Off to prevent filtering. Figure 5-5: System Tab-MISC Configuration Chapter 5: Configuring the Switch through the Web Utility 20 System Tab

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
20
Chapter 5: Configuring the Switch through the Web Utility
System Tab
24-port 10/100 + 2-Port Gigabit Switch with WebView
System Tab
The System tab displays the system information.
•
Firmware version. The current firmware version is displayed.
•
MAC Address. The MAC Address of the Switch is displayed.
•
IP Address. This IP Address of the network is displayed. (The default IP address is 192.168.1.254. Verify the
address. You can change the IP address, subnet mask, and default gateway here.
•
Subnet Mask. The subnet mask of the network is displayed.
•
Default Gateway. The default gateway of the network is displayed.
Click the
Apply
button after you have verified that the information is correct.
These following links are available on this tab:
To configure the advanced switch configuration, click the
Click here to configure MISC configuration
link.
To configure your username and password, click the
Click here to configure your Username/Password
link.
(Figure 5-6)
To reboot your system, click the
Click here to reboot system
link.
To restore the Switch back to the default settings, click the
Click here to restore system default setting
link.
Advanced Switch Configuration
(Figure 5-5.)
This screen allows you to make advanced switch configuration settings.
Broadcast Storm Filter. This allows you to filter by percentage the amount of broadcast traffic to your network to
prevent a storm of too many broadcasts from being sent at the same time. Select
5%
,
10%
, or
20%
from the
drop-down menu. Select
Off
to prevent filtering.
Figure 5-4: System Tab-System Information
Figure 5-5: System Tab-MISC Configuration