Craftsman 30084N Operation Manual - Page 18

Maintenance & Troubleshooting

Get Craftsman 30084N - 180 Amp 220 Volt Digital MIG Welder PDF manuals and user guides
UPC - 055249070420
View all Craftsman 30084N manuals
Add to My Manuals
Save this manual to your list of manuals

Page 18 highlights

SECTION 4 - MAINTENANCE & TROUBLESHOOTING 4-1. Routine Maintenance Y Disconnect power before maintaining. . Maintain more often during severe conditions. 3 Months Replace Damaged Or Unreadable Labels 6 Months Repair Or Replace Cracked Cables And Cords Clean And Tighten Weld Terminals Blow Out Or Vacuum Inside Remove drive roll and apply light coat of oil or grease to drive motor shaft. 4-2. Circuit Breakers CB1 And CB2 1 2 Y Turn Off unit. 1 Circuit Breaker CB1 CB1 protects the transformer from overload. If CB1 opens, wire feeding stops. 2 Circuit Breaker CB2 CB2 protects the trigger circuit from overload. If CB1 opens, weld output stops. Press button to reset circuit breaker. Close door. 4-3. Changing Drive Roll And Inlet Wire Guide Tools Needed: 1 2 OM-194 199 Page 15 Ref. ST-801 567 1 Drive Roll Choose correct drive roll for wire type, and install as shown. 2 Inlet Wire Guide Remove guide by pressing on barbed area, or cutting off one end near housing and pulling it out of hole. Push new guide into hole from rear until it snaps in place. Ref. ST-801 569-A

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
OM-194 199 Page 15
SECTION 4 – MAINTENANCE & TROUBLESHOOTING
4-1.
Routine Maintenance
Y
Disconnect power
before maintaining.
.
Maintain more often
during severe conditions.
3 Months
Replace
Damaged Or
Unreadable
Labels
Clean And
Tighten
Weld
Terminals
Repair Or
Replace
Cracked
Cables And
Cords
6 Months
Blow Out Or
Vacuum Inside
Remove drive roll
and apply light coat
of oil or grease to
drive motor shaft.
4-2.
Circuit Breakers CB1 And CB2
Ref. ST-801 567
Y
Turn Off unit.
1
Circuit Breaker CB1
CB1 protects the transformer from
overload. If CB1 opens, wire
feeding stops.
2
Circuit Breaker CB2
CB2 protects the trigger circuit from
overload. If CB1 opens, weld output
stops.
Press button
to
reset
circuit
breaker. Close door.
1
2
4-3.
Changing Drive Roll And Inlet Wire Guide
Ref. ST-801 569-A
1
Drive Roll
Choose correct drive roll for wire
type, and install as shown.
2
Inlet Wire Guide
Remove guide by pressing on
barbed area, or cutting off one end
near housing and pulling it out of
hole. Push new guide into hole from
rear until it snaps in place.
Tools Needed:
2
1