Cub Cadet RZT S 42 RZT S 42 Operator's Manual - Page 28

Flange Lock Nut

Get Cub Cadet RZT S 42 PDF manuals and user guides View all Cub Cadet RZT S 42 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

3. Remove the two idler pulleys by removing the hex screws and flange lock nuts that secure them to the deck and the idler arm. See Figure 7-8. Do not lose any of the hardware when removing the hex screw and flange lock nut. 46" Deck 1. Remove the deck from beneath the tractor, (refer to Deck Removal on page 26). 2. Remove the hex washer screws securing the belt covers to Hex Screw the deck. See Figure 7-9. Flange Lock Nut Pulley Cap Pulley Cap Hex Washer Screws Belt Cover Idler Pulleys Washer Belt Guard Flange Lock Nut Washer Belt Guard Idler Arm Hex Screw Spindle Pulley Belt Guard Spindle Pulley Idler Pulley Idler Arm Idler Pulley Figure 7-8 PTO Pulley NOTE: Take note of the position of the belt guards to ensure they are properly re-installed. 4. Remove the belt from the spindle pulleys. 5. Install the new belt around the spindle pulleys as shown and reinstall the belt covers. See Figure 7-7. Figure 7-9 3. Remove the two idler pulleys by removing the hex screws and flange lock nuts that secure them to the deck and the idler arm. See Figure 7-10. Do not lose any of the hardware when removing the hex screw and flange lock nut. 6. Place the belt around the idler pulleys removed in step 3 with the "V" side facing in. Once in place, reinstall all the hardware and tighten the flange lock nut to secure the Flange Lock Nut Pulley Cap Flange Lock Nut Pulley Cap assembly. See Figure 7-8. 7. Route the belt as shown in Figure 7-7 and then reinstall the deck. Idler Pulley Washer Belt Guard Idler Arm Idler Pulley Spacer Shoulder Spacer Hex Screw 28 Section 7- Service Flat Washer Hex Screw Figure 7-10 NOTE: Take note of the position of the belt guard to ensure they are properly re-installed. 4. Remove the belt from the spindle pulleys. 5. Install the new belt around the spindle pulleys as shown and reinstall the belt covers. See Figure 7-9.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
S
ECTION
7— S
ERVICE
28
3.
Remove the two idler pulleys by removing the hex screws
and flange lock nuts that secure them to the deck and the
idler arm. See Figure 7-8. Do not lose any of the hardware
when removing the hex screw and flange lock nut.
Hex Screw
Hex Screw
Pulley Cap
Pulley Cap
Washer
Belt Guard
Belt Guard
Washer
Idler Arm
Flange Lock Nut
Flange Lock Nut
Idler Pulleys
Figure 7-8
NOTE:
Take note of the position of the belt guards to
ensure they are properly re-installed.
4.
Remove the belt from the spindle pulleys.
5.
Install the new belt around the spindle pulleys as shown
and reinstall the belt covers. See Figure 7-7.
6.
Place the belt around the idler pulleys removed in step 3
with the “V” side facing in. Once in place, reinstall all the
hardware and tighten the flange lock nut to secure the
assembly. See Figure 7-8.
7.
Route the belt as shown in Figure 7-7 and then reinstall the
deck.
46” Deck
1.
Remove the deck from beneath the tractor, (refer to Deck
Removal on page 26).
2.
Remove the hex washer screws securing the belt covers to
the deck. See Figure 7-9.
PTO Pulley
Idler Pulley
Idler Pulley
Belt Cover
Hex Washer
Screws
Belt Guard
Spindle Pulley
Spindle Pulley
Idler Arm
Figure 7-9
3.
Remove the two idler pulleys by removing the hex screws
and flange lock nuts that secure them to the deck and the
idler arm. See Figure 7-10. Do not lose any of the hardware
when removing the hex screw and flange lock nut.
Pulley Cap
Washer
Flange Lock Nut
Flange Lock Nut
Pulley Cap
Idler Pulley
Idler Pulley
Belt Guard
Spacer
Shoulder Spacer
Idler Arm
Hex Screw
Flat Washer
Hex Screw
Figure 7-10
NOTE:
Take note of the position of the belt guard
to ensure
they are properly re-installed.
4.
Remove the belt from the spindle pulleys.
5.
Install the new belt around the spindle pulleys as shown
and reinstall the belt covers. See Figure 7-9.