D-Link DCS-2000 Product Manual - Page 125

Reset and Restore

Get D-Link DCS-2000 PDF manuals and user guides View all D-Link DCS-2000 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 125 highlights

Reset and Restore There is a button hidden in the pinhole beside the Ethernet socket. It is used to reset the system or restore the factory default settings. Sometimes resetting the DCS-2000 will return the system back to a normal state. If the system still has problems after reset, restore the factory settings and install again: RESET: 1. Lightly insert a paper clip (or a similar sized tool) into the reset hole on the back of the camera, press lightly and then release the button. 2. The LED on the front of the camera will begin blinking red and green fast. 3. When the LED stops the blinking fast and starts to blink once a second, the reset is completed. RESTORE: 1. Insert the paperclip or other tool and press and continuously hold down on the button recessed inside the reset hole. 2. Wait for the LED on the front of the camera to blink red and green and hold the button through two cycles of blinking (about 5-7 seconds.) 3. Withdraw the tool after the second cycle of the LED blinking and a factory restore has been completed. Reset button Restoring the factory defaults will result in the loss of any previous settings and will require running the Installation Wizard to return the DCS-2000 to user preferred settings. 125

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
125
There is a button hidden in the pinhole beside the Ethernet socket. It is
used to
reset
the system or
restore
the factory default settings. Sometimes
resetting the
DCS-2000
will return the system back to a normal state. If
the system still has problems after reset, restore the factory settings and
install again:
RESET
:
1.
3.
RESTORE
:
1.
2.
3.
Reset and Restore
Reset button
Restoring the factory defaults will result in the
loss of any previous settings and will require
running the Installation Wizard to return the
DCS-2000
to user preferred settings.
2. The LED on the front of the camera will begin blinking
red and green fast.
Lightly insert a paper clip (or a similar sized tool) into the
reset hole on the back of the camera, press lightly and
then release the button.
Insert the paperclip or other tool and press and continuously
hold down on the button recessed inside the reset hole.
Wait for the LED on the front of the camera to blink red
and green and hold the button through two cycles of
blinking (about 5-7 seconds.)
Withdraw the tool after the second cycle of the LED
blinking and a factory restore has been completed.
When the LED stops the blinking fast and starts to blink
once a second, the reset is completed.