D-Link DCS-5605 Product Manual - Page 41

Setting up a Wireless Connection with WPS

Get D-Link DCS-5605 PDF manuals and user guides
UPC - 790069334870
View all D-Link DCS-5605 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 41 highlights

Setting up a Wireless Connection with WPS If your wireless access point or router supports push-button Wireless Protected Setup (WPS), you can quickly configure your wireless network and camera without using the camera's web interface. After plugging the power adapter to your camera and the front status LED lights up, hold down the WPS button on the back of the camera for 3 seconds. After pressing the button, it should start flashing blue. Now press the WPS button on your router or access point within 1 minute to activate WPS and allow your devices to automatically configure a wireless connection. After WPS is successfully activated, the WPS LED on your camera will stop flashing, and will light up solid blue, then reboot. Note: On some routers/access points, you may need to enter the web interface to activate WPS. Consult your product's user manual for further assistance. D-Link DCS-5605/DCS-5635 User Manual 40

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
40
D-Link DCS-5605/DCS-5635 User Manual
If your wireless access point or router supports push-button Wireless Protected Setup (WPS), you can quickly configure your wireless
network and camera without using the camera’s web interface.
After plugging the power adapter to your camera and the front status LED lights up, hold down the WPS button on the back of the camera
for 3 seconds. After pressing the button, it should start flashing blue.
Now press the WPS button on your router or access point within 1 minute to activate WPS and allow your devices to automatically
configure a wireless connection. After WPS is successfully activated, the WPS LED on your camera will stop flashing, and will light up
solid blue, then reboot.
Note:
On some routers/access points, you may need to enter the web interface to activate WPS. Consult your product’s user manual for
further assistance.
Setting up a Wireless Connection with WPS