Dell Alienware Area-51 R4 Alienware Area-51 R5 Service Manual - Page 71

Replacing the front-bezel heat-sensor cable, Procedure, Post-requisites

Get Dell Alienware Area-51 R4 PDF manuals and user guides View all Dell Alienware Area-51 R4 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 71 highlights

Replacing the front-bezel heat-sensor cable NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the steps in Before working inside your computer. After working inside your computer, follow the instructions in After working inside your computer. For more safety best practices, see the Regulatory Compliance home page at www.dell.com/ regulatory_compliance. Procedure 1. Route the front-bezel heat-sensor cable through the bracket. 2. Align the tab on the front-bezel heat-sensor cable on the chassis. 3. Push the release tab on the front-bezel heat-sensor cable and press it into place. 4. Align and place the PCI fan holder from the chassis. 5. Replace the two screws (M3x5.25) that secure the PCI fan holder to the chassis. 6. Route the front-bezel heat sensor cable through the routing guides on the chassis. 7. Connect the front-bezel heat sensor cable to the system board. Post-requisites 1. Replace the PCI fan. 2. Replace the left and right side-panels. See "Replacing the side panels". 3. Replace the stability foot. 71

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
Replacing the front-bezel heat-sensor cable
NOTE: Before working inside your computer, read the safety information that shipped with your computer and follow the
steps in
Before working inside your computer
. After working inside your computer, follow the instructions in
After working
inside your computer
. For more safety best practices, see the Regulatory Compliance home page at
www.dell.com/
regulatory_compliance
.
Procedure
1.
Route the front-bezel heat-sensor cable through the bracket.
2.
Align the tab on the front-bezel heat-sensor cable on the chassis.
3.
Push the release tab on the front-bezel heat-sensor cable and press it into place.
4.
Align and place the PCI fan holder from the chassis.
5.
Replace the two screws (M3x5.25) that secure the PCI fan holder to the chassis.
6.
Route the front-bezel heat sensor cable through the routing guides on the chassis.
7.
Connect the front-bezel heat sensor cable to the system board.
Post-requisites
1.
Replace the
PCI fan
.
2.
Replace the left and right side-panels. See “
Replacing the side panels
”.
3.
Replace the
stability foot
.
71