Denon AVR 2809CI Owners Manual - English - Page 28
Step 2 : Measurement, Step 3 : Calculation, Step 4 : Check
UPC - 883795000635
View all Denon AVR 2809CI manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 28 highlights
Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting Specifications Step 2 : Measurement F Menu screen F q Auto Setup qw SP2atlnteedpae2sla:eirMsepthaleeAsaniuducigysrenhseegtymmMeipauncotltrstoiEptQhiooXnnTe.StNleoipws2t:meMenAeaiuasnAtsugudourysripseSenoyemgsMteiuun2tlptnitdoEnQ. XT Next Calculate Cancel Front L w Cancel Auto Setup r SP3atlrteedpae2sla:eirMsepthaleeAsaniuducigysrenhseegtymmMeipauncotltrstoiEptQhiooXnnTe.SteAwple2lr:eMtAehfuaeiAtsnudoumiysresseSeahyemseMteuduunr.lptetmEeQntXsT Next Calculate Retry Cancel Calculate Retry Cancel q Select "Next 0", then press o. • The measurement of the 2nd position starts. • Select "Calculate 0" with i, and press o to proceed to Step 3. w Move the microphone to the 3rd position and press o. • The measurement of the 3rd position starts. • Select "Calculate 0" with i, and press o to proceed to Step 3. e Perform repeatedly through the 6th position or more. A maximum of 8 position can be measured . r "All the measurements were finished." is displayed on the on- screen display, when you have completed measurements in 8th positions. • Select "Calculate 0", and press o to proceed to Step 3. Step 3 : Calculation F Menu screen F q Auto Setup Audyssey MultEQ XT Step3:Calculation Calculating Please wait... The values obtained from the measurements are automatically analyzed and the attributes for each of the speakers in the listening area are determined. q Select "Calculate 0" at Step 2, then press o. • Analysis begins. • Analysis takes several minutes to complete. • The time required for this analysis depends on the number of speakers connected. The greater the number of speakers connected, the longer analysis will take. NOTE • Do not change the speaker connections or subwoofer volume, or speaker locations after making measurements. If changes are necessary, make the changes and use Audyssey MultEQ XT auto setup once again for an updated EQ solution. • For instance, if the location or direction of a speaker is altered, the Auto Setup should be performed again to ensure the correct EQ solution for the new room configuration. Step 4 : Check F Menu screen F q Auto Setup Audyssey MultEQ XT Step4:Check Please check the results of the measured item. Speaker Config.Check Distance Check Channel Level Check Crossover Freq.Check Next When analysis is complete, check the analysis results for the following four items. q Make your selection using ui and press ENTER. • Presence and size of speaker "Speaker Config. Check" • Distance of speaker from listening position "Distance Check" • Speaker channel level "Channel Level Check" • Crossover Frequency "Crossover Freq. Check" w Use ui to change which speaker is displayed. e Press RETURN. This returns you to analysis results items, so repeat step q. r Press i to select "Next 0", and then press o to proceed to Step 5. Distance values that are greater than the actual distance of a speaker may be accurate for speakers with built-in filters (subwoofers, etc). This is because these filters add electrical delay (distance) to the signal that is compensated for by the Auto Setup process. n To cancel Auto Setup Press ui to select "Cancel 0", then press o. After completing a measurement position, move the microphone to the next position. Measure at least 6 positions: the main listening position and 5 other surrounding positions. Although it is allowable to measure less than 6 positions, it is recommended to measure 6 or more positions (with a maximum of 8 positions) for best results.