Denon AVR 2809CI Owners Manual - English - Page 56

Presetting Radio Channels, Preset Memory, Listening to Preset Channels, Checking the XM Signal

Get Denon AVR 2809CI - AV Receiver PDF manuals and user guides
UPC - 883795000635
View all Denon AVR 2809CI manuals
Add to My Manuals
Save this manual to your list of manuals

Page 56 highlights

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting Specifications Symbols used to indicate buttons in this manual Button located on both the main unit and the remote control unit Button only on the main unit Button only on the remote control unit BUTTON [BUTTON] uiop Checking the XM Signal Strength and Radio ID 1 Either turn or press [SAT TU2] (AMP mode) to select "XM". 2 Press until "SIGNAL" appears on the display. The display will switch as shown below, depending on the reception conditions. Display GOOD MARGINAL WEAK NO Status Signal strength is good Signal strength is marginal Signal strength is weak No signal Presetting Radio Channels (Preset Memory) Your favorite broadcast channels can be preset so that you can tune them in easily. Up to 56 channels can be preset. 1 Tune in the broadcast channel you want to preset. 2 Press [MEMO]. 3 Press [A ~ G] to select the block in which the channel is to be preset. 4 Press [CHANNEL + -] or [NUMBER (1 ~ 8)] to select the preset number. 3 5 Adjust the position of the antenna until "SIGNAL: GOOD" is shown on the display. Press [MEMO] again to complete the setting. XM [ SAT TU] ( mode) [A ~ G] [ ] [MEMO] [SEARCH] uiop [ENTER] [CHANNEL + -] [SAT TU2] (AMP mode) [NUMBER] SIRIUS 4 Press until the channel you want to check (example: "XM001") is displayed. To preset other channels, repeat steps 1 to 5. [ ( 5 SAT TU] mode) Press [ ] and select channel 0 (XM000). The radio ID is shown on the display. NOTE Preset channels are erased by overwriting them. [A ~ G] [ ] [MEMO] Radio ID [SEARCH] uiop The strength of both the XM satellite and terrestrial signals can be checked at menu "Input Setup" - "Antenna Aiming" (vpage 39). [CHANNEL + -] [SAT TU1] (AMP mode) [NUMBER] Listening to Preset Channels Operation on the Main Unit Press , then turn to select the preset channel. Operation on the Main Remote control Unit. 1 Press [A ~ G] to select the memory block (A to G). 2 Press [CHANNEL + -] or [NUMBER (1 ~ 8)] to select the desired preset channel. 

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
µ³
Getting Started
Connections
Setup
Remote Control
Multi-zone
Information
Troubleshooting
Specifications
Presetting Radio Channels
(Preset Memory)
Your favorite broadcast channels can be preset so that you can
tune them in easily. Up to 56 channels can be preset.
To preset other channels, repeat steps 1 to 5.
NOTE
Preset channels are erased by overwriting them.
1
Press
[A ~ G]
to select the memory block (A to G).
2
Press
[CHANNEL + –]
or
[NUMBER (1 ~ 8)]
to select
the desired preset channel.
Listening to Preset Channels
1
Tune in the broadcast channel you want to preset.
2
Press
[MEMO]
.
3
Press
[A ~ G]
to select the block in which the channel
is to be preset.
4
Press
[CHANNEL + –]
or
[NUMBER (1 ~ 8)]
to select
the preset number.
5
Press
[MEMO]
again to complete the setting.
The strength of both the XM satellite and terrestrial signals can be
checked at menu “Input Setup” – “Antenna Aiming” (
v
page 39).
Checking the XM Signal Strength and
Radio ID
1
Either turn
<SOURCE SELECT>
or press
[SAT TU2]
(AMP mode) to select “XM”.
2
Press
<STATUS>
until “SIGNAL” appears on the
display.
The display will switch as shown below, depending on the
reception conditions.
Display
Status
GOOD
Signal strength is good
MARGINAL
Signal strength is marginal
WEAK
Signal strength is weak
NO
No signal
3
Adjust the position of the antenna until “SIGNAL:
GOOD” is shown on the display.
4
Press
<STATUS>
until the channel you want to check
(example: “XM001”) is displayed.
5
Press
[
]
and select channel 0 (XM000).
The radio ID is shown on the display.
Radio ID
Operation on the Main Unit
<SOURCE SELECT>
<TUNING PRESET>
<STATUS>
uiop
Press
<TUNING PRESET>
, then turn
<SOURCE SELECT>
to select the preset channel.
Operation on the Main Remote control Unit.
Button located on both the main unit
and the remote control unit
BUTTON
Button only on the main unit
<BUTTON>
Button only on the remote control unit
[BUTTON]
Symbols used to indicate buttons in this manual
[NUMBER]
[MEMO]
[A ~ G]
[CHANNEL + –]
[
SAT TU]
[SEARCH]
uiop
[SAT TU1]
[
]
[NUMBER]
[MEMO]
[A ~ G]
[CHANNEL + –]
[SAT TU2]
[
SAT TU]
[SEARCH]
[ENTER]
uiop
[
]
(
mode)
(AMP mode)
XM
SIRIUS
(
mode)
(AMP mode)
Playback