Denon AVR 2809CI Owners Manual - English - Page 49

Getting Started Connections Setup Playback Remote Control Multi-zone Information Troubleshooting Specifications S2 Dynamic EQ Audyssey Dynamic EQ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ XT to provide well-balanced sound for every listener at any volume level. [Selectable items] ON : Use Dynamic EQ function. OFF : Do not use Dynamic EQ function. Operating from the main unit or main remote control unit Press DYNAMIC VOLUME. Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF Dynamic EQ / Volume : OFF • " Dynamic EQ" can only be set when auto setup has been performed. • After performing "Auto Setup", the "Dynamic EQ" setting automatically becomes "ON". • " Dynamic EQ" cannot be set in the following situations. ⋅ If "Auto Setup" fails to be completed. ⋅ After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • W hen "MultEQ XT" is set to "OFF" or "Manual", "Dynamic EQ" is automatically set to "OFF". • B efore running Auto Setup and after running Auto Setup, if the number of speakers has increased or you pressed DYNAMIC VOLUME, "Run Audyssey" is displayed. In this case, either perform Auto Setup, or return to the setting after running Auto Setup with "Auto Setup" - "Parameter Check" - "Restore". NOTE When you set "Dynamic EQ" to "ON", "Tone Control" and "Night Mode" are switched "OFF". n Operating conditions for each function • D ynamic EQ : When "MultEQ XT" is set to "ON" • D ynamic Volume : When "Dynamic EQ" is set to "ON" • S etting : When "Dynamic Volume" is set to "ON" S1 MultEQ XT S2 Dynamic EQ S3 Dynamic Volume S4 Setting S3 Dynamic Volume Audyssey Dynamic Volume solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same. [Selectable items] ON : Use Dynamic Volume. The Dynamic Volume effect will be at the level of the "Setting". OFF : Do not use Dynamic Volume. Operating from the main unit or main remote control unit Press DYNAMIC VOLUME. Dynamic EQ / Volume : ON Dynamic EQ : ON / Volume : OFF "Green" "Red" Dynamic EQ / Volume : OFF "Off" • "Dynamic Volume" can only be set when auto setup has been performed. • "Dynamic Volume" cannot be set in the following situations. ⋅ If "Auto Setup" fails to be completed. ⋅ After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. • When "MultEQ XT" is set to "OFF" or "Manual", "Dynamic Volume" is automatically set to "OFF". • Before running Auto Setup and after running Auto Setup, if the number of speakers has increased or you pressed DYNAMIC VOLUME, "Run Audyssey" is displayed. In this case, either perform Auto Setup, or return to the setting after running Auto Setup with "Auto Setup" - "Parameter Check" - "Restore". NOTE "Dynamic Volume" and "Night Mode" cannot be used jointly. S4 Setting Can be set when "Dynamic Volume" is set to "ON". Set Dynamic Volume effect. [Selectable items] Midnight : High setting affects volume the most, causing all sounds to be of equal loudness. Evening : Middle setting prevents loud and soft sounds from being much louder and softer respectively than average sounds. Day : Low setting provides the least adjustments to the loudest and softest of sounds. NOTE • " Setting" can only be set when auto setup has been performed. • " Setting" cannot be set in the following situations. ⋅ If "Auto Setup" fails to be completed. ⋅ After running Auto Setup, when the number of used speakers has increased from the number of measured speakers. ⋅ If "Dynamic Volume" setting is "OFF". About Dynamic EQ Audyssey Dynamic EQ™ solves the problem of deteriorating sound quality as volume is decreased by taking into account human perception and room acoustics. Dynamic EQ selects the correct frequency response and surround levels moment-by-moment at any user-selected volume setting. The result is bass response, tonal balance, and surround impression that remain constant despite changes in volume. Dynamic EQ combines information from incoming source levels with actual output sound levels in the room, a prerequisite for delivering a loudness correction solution. Audyssey Dynamic EQ works in tandem with Audyssey MultEQ XT to provide well-balanced sound for every listener at any volume level. About Dynamic Volume Audyssey Dynamic Volume™ solves the problem of large variations in volume level between television programs, commercials, and between the soft and loud passages of movies. Dynamic Volume looks at the preferred volume setting by the user and then monitors how the volume of program material is being perceived by listeners in real time to decide whether an adjustment is needed. Whenever necessary, Dynamic Volume makes the necessary rapid or gradual adjustments to maintain the desired playback volume level while optimizing the dynamic range. Audyssey Dynamic EQ is integrated into Dynamic Volume so that as the playback volume is adjusted automatically, the perceived bass response, tonal balance, surround impression, and dialog clarity remain the same whether watching movies, flipping between television channels, or changing from stereo to surround sound content. For details on adjusting individual parameters, see "Adjusting the parameters" (vpage 42). 46