Denon AVR 787 Owners Manual - English - Page 60

Test Tone], Enter

Get Denon AVR 787 - AV Receiver PDF manuals and user guides
UPC - 081757507172
View all Denon AVR 787 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

ENGLISH Advanced Setup - Part 2 ¢ Adjusting the test tone using the remote control unit Adjustment of the test tones using the remote control unit is only possible in the "Auto" mode and only valid in the STANDARD (Dolby/ DTS Surround) mode. The adjusted levels are automatically stored for the different surround modes. 1 Press [TEST TONE]. • Test tones are output from the different speakers. • The crossover frequency mode is valid only when subwoofer is set to "ON", and when one or more speakers are set to "Small", as described in section "Setting the Speaker Configuration" ( page 54, 55). • If "LFE+Main" is set at "Subwoofer Setup", "SW:LFE+Main" ( page 55) is displayed at the top right of the screen. 2 Press F G to adjust the volume. 3 Press [TEST TONE]. • Set to "80 Hz" when using regular speakers. When using small speakers, we recommend setting to a higher frequency. Setting the Crossover Frequency Set the frequency (Hz) below which the bass sound of the various speakers is to be output from the subwoofer. For speakers that are set to "Small", frequencies under the crossover frequency are cut before the signal is output, and the low frequency component that was cut is output from the subwoofer or the speakers that are set to "Large". 1 Press D H to select "Crossover Frequency", then press ENTER. 2 Press F G to set. 40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz: Set as desired according to your speakers' bass playback ability. 3 Press ENTER. 1 2 57 ENGLISH Advanced Setup - Part 2

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
ENGLISH
57
ENGLISH
Advanced Setup – Part 2
Advanced Setup – Part 2
¢
Adjusting the test tone using the remote control
unit
Adjustment of the test tones using the remote control unit is only
possible in the “Auto” mode and only valid in the STANDARD (Dolby/
DTS Surround) mode. The adjusted levels are automatically stored for
the different surround modes.
Press
[TEST TONE]
.
• Test tones are output from the different speakers.
Press
[TEST TONE]
.
Press
FG
to adjust the volume.
1
2
3
Setting the Crossover Frequency
Set the frequency (Hz) below which the bass sound of the various
speakers is to be output from the subwoofer.
For speakers that are set to “Small”, frequencies under the crossover
frequency are cut before the signal is output, and the low frequency
component that was cut is output from the subwoofer or the
speakers that are set to “Large”.
Press
DH
to select “Crossover Frequency”, then
press
ENTER
.
1
Press
FG
to set.
40, 60, 80, 90, 100, 110, 120, 150, 200, 250 Hz:
Set as desired according to your speakers’ bass playback ability.
2
Press
ENTER
.
3
• The crossover frequency mode is valid only when subwoofer is set
to “ON”, and when one or more speakers are set to “Small”, as
described in section “Setting the Speaker Configuration” (
page
54, 55).
• If “LFE+Main” is set at “Subwoofer Setup”, “SW:LFE+Main” (
page 55) is displayed at the top right of the screen.
• Set to “80 Hz” when using regular speakers. When using small
speakers, we recommend setting to a higher frequency.
1
2