Epson 2070 User Manual - Page 119

Options, The Paper Does Not Feed Properly With fhe Cut-sheet Feeder

Get Epson 2070 - LQ B/W Dot-matrix Printer PDF manuals and user guides
UPC - 010343812277
View all Epson 2070 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 119 highlights

The paper may have too much slack. Adjust the position of the sprockets to take up any slack along the width of the paper. Remove slack lengthwise by rotating the knob of the pull tractor. The paper does not eject properly. Tear off the paper entering the printer, then press the LF/FF or Load/Eject button to feed the paper forward. See "Using the Tear-Off Function" in Chapter 3. When you switch between single sheets and continuous paper, the printer beeps several times and the Pause light comes on. You may have tried to change the paper release lever position while paper was still in the printer. Return the paper release lever to the original position and eject the paper. Then change the lever position. Options See this section if you have problems with optional equipment. The paper does not feed properly with fhe cut-sheet feeder The paper does not feed. The cut-sheet feeder may be incorrectly installed. Reinstall it as described in Chapter 4. You may have loaded too many sheets in the cut-sheet feeder's bin. Make sure the bin contains no more than 150 sheets. Troubleshooting 6-9

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
The paper may have too much slack. Adjust the position of
the sprockets to take up any slack along the width of the paper.
Remove slack lengthwise by rotating the knob of the pull
tractor.
The paper does not eject properly.
Tear off the paper entering the printer, then press the
LF/FF
or
Load/Eject
button to feed the paper forward. See “Using the
Tear-Off Function” in Chapter 3.
When you switch between single sheets and continuous paper, the
printer beeps several times and the
Pause
light comes on.
You may have tried to change the paper
release lever position
while paper was still in the printer. Return the paper release
lever to the original position and eject the paper. Then change
the lever position.
Options
See this section if you have problems with optional equipment.
The paper does not
feed
properly with fhe cut-sheet
feeder
The paper does not feed.
The cut-sheet feeder may be incorrectly installed. Reinstall it as
described in Chapter 4.
You may have loaded too many sheets in the cut-sheet feeder’s
bin. Make sure the bin contains no more than 150 sheets.
Troubleshooting 6-9