Epson BrightLink Pro 1450Ui Installation Guide - Control Pad and Touch Unit - Page 5

If the distance from the wall to the surface of the whiteboard is greater than 2 inches 51 mm,

Get Epson BrightLink Pro 1450Ui PDF manuals and user guides View all Epson BrightLink Pro 1450Ui manuals
Add to My Manuals
Save this manual to your list of manuals

Page 5 highlights

• When installing the Touch Unit within the frame of the whiteboard, secure the Touch Unit with magnets or screws. Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen holders, or thick frames in the shaded areas in the following figure. The Touch Unit will not operate correctly if anything is obstructing the infrared signal. 4.0 in. (100 mm) 4.0 in. (100 mm) 0.8 in. (20 mm) • When installing the touch unit above the frame of a whiteboard, use the included Touch Unit Bracket. • If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you must install the Touch Unit on the whiteboard. • If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you must install the Touch Unit on the whiteboard or screen. 4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
4
•
When installing the Touch Unit within the frame of the whiteboard, secure the Touch Unit with magnets
or screws.
Make sure there are no obstacles, such as cables, or protruding objects such as whiteboard trays, pen
holders, or thick frames in the shaded areas in the following figure. The Touch Unit will not operate
correctly if anything is obstructing the infrared signal.
•
When installing the touch unit above the frame of a whiteboard, use the included Touch Unit Bracket.
•
If the distance from the wall to the surface of the whiteboard is greater than 2 inches (51 mm), you
must install the Touch Unit on the whiteboard.
•
If the frame of the whiteboard extends more than 0.1 inch (3 mm) away from the board surface, you
must install the Touch Unit on the whiteboard or screen.
0.8 in. (20 mm)
4.0 in. (100 mm)
4.0 in. (100 mm)