Garmin Edge 130 Plus Owners Manual - Page 17

Device Information Specifications Edge 130 Plus Specifications Battery type Battery life Rechargeable, built-in lithium-ion battery Up to 12 hr. Operating temperature range From -20º to 60ºC (from -4º to 140ºF) Charging temperature range From 0º to 45ºC (from 32º to 113ºF) Wireless frequency Water rating 2.4 GHz @ 5.6 dBm nominal IEC 60529 IPX71 Heart Rate Monitor Specifications Battery type Battery life Water resistance User-replaceable CR2032, 3 V Up to 3.5 yr. at 1 hr./day 1 ATM2 NOTE: This product does not transmit heart rate data while swimming. Operating temperature From -5° to 50°C (from 23° to 122°F) range Wireless frequency/ protocol 2.4 GHz @ 2 dBm nominal • Machine wash the strap after every seven uses. • Do not put the strap in a dryer. • When drying the strap, hang it up or lay it flat. • To prolong the life of your heart rate monitor, unsnap the module when not in use. User Replaceable Batteries WARNING See the Important Safety and Product Information guide in the product box for product warnings and other important information. Replacing the Heart Rate Monitor Battery 1 Use a small Phillips screwdriver to remove the four screws on the back of the module. 2 Remove the cover and battery. Speed Sensor and Cadence Sensor Specifications Battery type User-replaceable CR2032, 3 V Battery life Speed sensor storage Operating temperature range Wireless frequency/protocol Water rating Approximately 12 mo. at 1 hr./day Up to 300 hr. of activity data From -20º to 60ºC (from -4º to 140ºF) 2.4 GHz @ 4 dBm nominal IEC 60529 IPX71 Device Care NOTICE Do not store the device where prolonged exposure to extreme temperatures can occur, because it can cause permanent damage. Avoid chemical cleaners, solvents, and insect repellents that can damage plastic components and finishes. Secure the weather cap tightly to prevent damage to the USB port. Avoid extreme shock and harsh treatment, because it can degrade the life of the product. Cleaning the Device 1 Wipe the device using a cloth dampened with a mild detergent solution. 2 Wipe it dry. After cleaning, allow the device to dry completely. Caring for the Heart Rate Monitor NOTICE You must unsnap and remove the module before washing the strap. A build up of sweat and salt on the strap can decrease the ability of the heart rate monitor to report accurate data. • Go to www.garmin.com/HRMcare for detailed washing instructions. • Rinse the strap after every use. 1 The device withstands incidental exposure to water of up to 1 m for up to 30 min. For more information, go to www.garmin.com/waterrating. 2 The device withstands pressure equivalent to a depth of 10 m. For more information, go to www.garmin.com/waterrating. Device Information 3 Wait 30 seconds. 4 Insert the new battery with the positive side facing up. NOTE: Do not damage or lose the O-ring gasket. 5 Replace the back cover and the four screws. NOTE: Do not overtighten. After you replace the heart rate monitor battery, you may need to pair it with the device again. Replacing the Cadence Sensor Battery The device uses one CR2032 battery. The LED flashes red to indicate a low battery level after two revolutions. 1 Locate the circular battery cover on the back of the sensor. 2 Twist the cover counter-clockwise until the marker points to unlocked and the cover is loose enough to remove. 3 Remove the cover and the battery . 4 Wait 30 seconds. 5 Insert the new battery into the cover, observing polarity. NOTE: Do not damage or lose the O-ring gasket. 6 Twist the cover clockwise until the marker points to locked. NOTE: The LED flashes red and green for a few seconds after battery replacement. When the LED flashes green and 13