Genie SilentMax 1000 Owner's Manual

Genie SilentMax 1000 Manual

Get Genie SilentMax 1000 PDF manuals and user guides View all Genie SilentMax 1000 manuals
Add to My Manuals
Save this manual to your list of manuals

Genie SilentMax 1000 manual content summary:

  • Genie SilentMax 1000 | Owner's Manual - Page 1
    GARAGE DOOR OPENER MODELS PowerMax® 1200/1500, SC 1200/1500, TriloGTM 1200/1500, PowerLift® 900, GPowerTM 900, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200 SCREW/BELT/CHAIN DRIVES OPERATION & MAINTENANCE MANUAL Includes INTELLICO®DE 2 Remote Control. Safe-T-Beam® System must be installed
  • Genie SilentMax 1000 | Owner's Manual - Page 2
    Controls 5 Travel Limits Closing Garage Door (DOWN Limits 6 Opening Garage Door (UP Limits 7 Wall Console Overview 8 Series III Wall Consoles with Black Buttons... 8 Series II Wall Consoles with White Buttons.... 8 Force and Speed Control 9 Contact Reverse Test 9 Remotes
  • Genie SilentMax 1000 | Owner's Manual - Page 3
    NOT connect the operator to the source of power until instructed to do so. • Locate the wall console button: A) Within sight of door. B) At a minimum height of 5 feet so small children cannot reach it. C) Away from all moving parts of the door. • Install the entrapment WARNING label next to the
  • Genie SilentMax 1000 | Owner's Manual - Page 4
    garage. The wall console has an indicator light with: Open/Close, Sure-Lock™, and independent light control buttons. Home Link and Car2U® compatible. Refer to the programming instructions on page 11. NOTE: Use this manual ONLY after completing assembly and installation of opener. Review Assembly
  • Genie SilentMax 1000 | Owner's Manual - Page 5
    Limits programming allows you to set how far your door travels up or down in opening and closing your garage door. Remote Programming synchronizes your remote control devices (remotes, wall console, and keypad) with the powerhead. Force Control refers to how much power is needed to move (open
  • Genie SilentMax 1000 | Owner's Manual - Page 6
    to the opener can occur. • T he shuttle MUST be engaged to carriage BEFORE setting limits. See Installation Poster (if provided) or call Customer Service at 1-800-35GENIE or visit www.geniecompany.com 3 Release down arrow button (-) and the long LED will begin flashing. PROGRAM SET + NOTE: If
  • Genie SilentMax 1000 | Owner's Manual - Page 7
    flash blue and go off). PROGRAM PROGRAM - + SET The DOWN (closed) limit is programmed. 8 Press and hold the up arrow button (+) until door is fully open, then release. Watch carriage as it approaches the power head to avoid contact with powerhead. PROGRAM SET - HOLD Opening Garage Door
  • Genie SilentMax 1000 | Owner's Manual - Page 8
    work normally. Independent Light Control Button Controls door opener lights from inside garage. 8 Series III Wall Consoles with Black Buttons Indicator Light Indicator light will display Red when wall console is properly wired and Sure-Lock™ is OFF. When Sure-Lock™ is ON, indicator light flashes
  • Genie SilentMax 1000 | Owner's Manual - Page 9
    Speed controls DO NOT require programming. Force and Speed Limits are factory set and rarely require adjustments. Making adjustments to these settings is covered in Troubleshooting Section of this manual (pages 18-19). 10 Open and close your garage door using the Wall Console Open/Close button. 13
  • Genie SilentMax 1000 | Owner's Manual - Page 10
    steps. 14 Press and hold the Program Set button (the round LED turns blue). 16 Remove protective film for battery from remote. PUL PROGRAM - + HOLD 2 seconds 15 Release the Program Set button (the long LED begins flashing purple). PROGRAM 17 Press and release the button you have choosen on the
  • Genie SilentMax 1000 | Owner's Manual - Page 11
    To program the same Remote for other garage door openers, repeat the steps above using one of the other two Remote buttons. Each Remote can be programmed for three door openers. BASIC PROGRAMMING IS COMPLETE AND YOUR GARAGE DOOR IS READY TO USE! PROGRAM SET - NOTE: For Car2U and HomeLink, park
  • Genie SilentMax 1000 | Owner's Manual - Page 12
    Press and hold Program Set key for 2 seconds. (The round LED turns blue and then goes o . The long LED will begin ashing purple Opener 2. Enter your PIN. 3. Press Up/Down key . Opener LEDs will stay on steady. Note: For multiple doors, see the full instructions packed with the keypad. 12 1. Enter
  • Genie SilentMax 1000 | Owner's Manual - Page 13
    up arrow button (+) and down arrow button (-) simultaneously on the Powerhead and hold until both LEDs flash blue and then go OFF. PROGRAM PROGRAM SET SET HOLD HOLD If the memory has been cleared, the Remote will not activate the door opener. NOTE: The garage door opener will operate normally
  • Genie SilentMax 1000 | Owner's Manual - Page 14
    4 Optional Programming INTELLICODE® 1 REMOTES Remotes provided with this unit can operate other (Intellicode® 1) models of Genie® garage door openers .The default Intellicode® 2 setting must be changed to Intellicode® 1. (Follow these same steps to change Intellicode® 1 back to Intellicode® 2.)
  • Genie SilentMax 1000 | Owner's Manual - Page 15
    /belt drive models: One-Piece Doors will only accept a straight door arm. Straight door arm 3/8"-16 x 7/8" Bolt 3/8" Lock nut Straight door arm (not included) 2 Secure door arm to the door bracket and with clevis pin and cotter pin. Door bracket Cotter pin Straight door arm G999-393 Manual
  • Genie SilentMax 1000 | Owner's Manual - Page 16
    hesitate to contact customer service at: 1-800-35-GENIE or visit www.geniecompany.com Important Safety Instructions WARNING TO REDUCE THE RISK OF SEVERE injury or death, READ AND FOLLOW ALL INSTRUCTIONS. 1. NEVER let children operate or play with the door controls. 2. Keep remote away from children
  • Genie SilentMax 1000 | Owner's Manual - Page 17
    opener. • Test light operation. Reset Open/Close Travel Limit Performing all eleven (11) Limits/Force setting steps (see pages 6-8) erases previous Limits/Force settings. Note: The opener will not close the door automatically unless the Safe-T-Beam® System is installed and Limits are programmed
  • Genie SilentMax 1000 | Owner's Manual - Page 18
    reverse before closing. 3. Doors that start up, but STOP before they completely open. Force Adjustment Action 1 Press and hold both up and down buttons 2 seconds or until round LED turns RED. 2 Press either until you reach desired setting. 3 Press and release. PROGRAM SET 4 Press either until
  • Genie SilentMax 1000 | Owner's Manual - Page 19
    Low OFF Blue Purple Red Powerhead LEDs LONG LED ROUND LED RED RED PURPLE PURPLE BLUE BLUE Note: One-piece doors are automatically set to the slowest speed during Limits programming and cannot be adjusted. Note: PowerLift® 900, GPower™ 900 openers DO NOT have speed adjustments. There are
  • Genie SilentMax 1000 | Owner's Manual - Page 20
    COVER MAY CAUSE ELECTRIC SHOCK. Disconnect power from opener prior to removing cover. POWER CORD CONNECTOR WHITE PRINTED CIRCUIT BOARD BLACK GREEN CHOKE * WHITE WHITE BLACK BLACK 76 5432 1 CHAIN MOTOR BLACK RED SCREW DRIVE MOTOR RED BLACK 1234 STRIPED WHITE STB 1 2 BWC 3 4 (IWC
  • Genie SilentMax 1000 | Owner's Manual - Page 21
    , and door spring. • Check opening "FORCE" adjustment. See page 8. •  WARNING: If you suspect a problem with the garage door hardware or springs, contact The Genie Company at 1-800-35GENIE. Door opener starts for • Button stuck on wall console or remote. no reason. • Was a remote lost or
  • Genie SilentMax 1000 | Owner's Manual - Page 22
    ON/RED/ STEADY ON/RED/ FLASHING OFF OFF ON/RED/ FLASHING OFF OFF OFF ON/RED/ FLASHING ON/RED/ STEADY Possible Problem Normal operation. No response from unit. Solution None required. Check power supply. Contact a trained door system technician. Limits NOT set properly. Re-program limits, see
  • Genie SilentMax 1000 | Owner's Manual - Page 23
    /1200 LIMITED WARRANTY GMI Holdings, Inc d/b/a The Genie Company ("Seller") warrants to the original purchaser of the below identified, SilentMax® 1000/1200, CB 1000/1200, IntelliG® 1000/1200, PowerMax® 1200/1500, SC 1200/1500, TriloG™ 1200/1500, PowerLift® 900, or GPower™ 900 garage door openers
  • Genie SilentMax 1000 | Owner's Manual - Page 24
    ? Genie-Net™ technology "tells" you! Closed Confirm™ Wireless Remote (Works with Revolution Series 1500, 1200 and 1000 Models) • Sleek and compact design • Beeps and flashes green when garage door closes. Gives warning tone and flashes red when garage door does not close properly • Network Adapter
  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
For Answers and Assistance:
1.800.354.3643
or visit www.geniecompany.com
SAVE THIS MANUAL FOR FUTURE REFERENCE
INSTALLER: LEAVE THIS MANUAL WITH HOMEOWNER
GARAGE DOOR OPENER MODELS
PowerMax
®
1200/1500, SC 1200/1500, TriloG
TM
1200/1500, PowerLift
®
900, GPower
TM
900,
SilentMax
®
1000/1200, CB 1000/1200, IntelliG
®
1000/1200
SCREW/BEL
T/CHAIN DRIVES
OPERA
TION & MAINTENANCE MAN
UAL
Genie, Genie logo, Intellicode, Safe-T-Beam, IntelliG, PowerMax, PowerLift, ChainMax and SilentMax are registered trademarks TriloG and GPower are trademarks of GMI Holdings, Inc., dba The Genie Company
Homelink is a registered trademark of Johnson Controls Technology Company. Car2U is a registered trademark of Lear Corporation. ©The Genie Company 2012 PN#38209501773, 9/2012
WARNING
T
o reduce the risk of injury to persons or damage to property – Use this opener only with a one-piece or sectional door
.
38209501773
Need help or have questions? DO NOT RETURN to the store
.
Call us
:
800-354-3643
Includes INTELLICODE
®
2 Remote Control. Safe-T-Beam
®
System must be installed to close door.
For use only with residential sectional or one piece overhead garage doors.
Homelink
®
and Car2U
®
compatible.