Gigabyte Z590 AORUS XTREME WATER User Manual - Page 66

B. Configuring SATA controller mode in BIOS Setup, C. UEFI RAID Configuration

Get Gigabyte Z590 AORUS XTREME WATER PDF manuals and user guides View all Gigabyte Z590 AORUS XTREME WATER manuals
Add to My Manuals
Save this manual to your list of manuals

Page 66 highlights

B. Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup. Steps: Turn on your computer and press to enter BIOS Setup during the POST (Power-On Self-Test). Go to Settings\IO Ports\SATA And RST Configuration, make sure SATA Controller(s) is enabled. To create RAID, set SATA Mode Selection to Intel RST Premium With Intel Optane System Acceleration. Then save the settings and restart your computer (Figure 1). Note: When using a PCIe SSD, make sure to set the RST Control PCIe Storage Devices item under Settings\IO Ports\SATA And RST Configuration to Manual. Then depending the M.2 connector you use, set the corresponding PCIe Storage Dev on Port XX item to RST Controlled. Finally, save the settings and exit BIOS Setup. Figure 1 C. UEFI RAID Configuration Step 1: After the system reboot, enter BIOS Setup again. Then enter the Settings\IO Ports\Intel(R) Rapid Storage Technology sub-menu (Figure 2). Figure 2 The BIOS Setup menus described in this section may differ from the exact settings for your motherboard. The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version. Configuring a RAID Set - 66 -

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
- 66 -
Configuring a RAID Set
The BIOS Setup menus described in this section may differ from the exact settings for your motherboard.
The actual BIOS Setup menu options you will see shall depend on the motherboard you have and
the BIOS version.
B. Configuring SATA controller mode in BIOS Setup
Make sure to configure the SATA controller mode correctly in system BIOS Setup.
Steps:
Turn on your computer and press <Delete> to enter BIOS Setup during the POST (Power-On Self-Test). Go
to
Settings\IO Ports\SATA And RST Configuration
, make sure
SATA Controller(s)
is enabled. To create
RAID, set
SATA Mode Selection
to
Intel RST Premium With Intel Optane System Acceleration
. Then save
the settings and restart your computer (Figure 1). Note: When using a PCIe SSD, make sure to set the
RST
Control PCIe Storage Devices
item under
Settings\IO Ports\SATA And RST Configuration
to
Manual
.
Then depending the M.2 connector you use, set the corresponding
PCIe Storage Dev on Port XX
item to
RST
Controlled
. Finally, save the settings and exit BIOS Setup.
Figure 1
C. UEFI RAID Configuration
Step 1:
After the system reboot, enter BIOS Setup again. Then enter the
Settings\IO Ports\Intel(R) Rapid Storage
Technology
sub-menu (Figure 2).
Figure 2