Haier HT18TS45SW HT18TW10SW - Page 10

Door Handle Installation - parts

Get Haier HT18TS45SW PDF manuals and user guides View all Haier HT18TS45SW manuals
Add to My Manuals
Save this manual to your list of manuals

Page 10 highlights

ENGLISH DOOR HANDLE INSTALLATION DOOR HANDLE INSTALLATION For refrigerators with a mounting screw installed on the face of both doors: Remove both handles from inside freezer compartment and screws from parts-included bag. FREEZER DOOR HANDLE 1. Place the tapered end of the handle over the mounting screw on the freezer door and gently slide handle in the direction of the flat end of the handle. (Fig. 1) 2. Once the handle is fully seated around the mounting screw, slowly rotate the flat end of the handle toward the bottom of the freezer door. Fig. 1 3. Open the freezer door and install the screws into the underside of the freezer door through the flat end of the handle. Do not use power tools to install screws. Do not over-tighten the screws. Fig. 2 REFRIGERATOR DOOR HANDLE 1. Place the tapered end of the handle over the mounting screw on the refrigerator door and gently slide handle in the direction of the flat end of the handle. (Fig. 1) 2. Once the handle is fully seated around the mounting screw, slowly rotate the flat end of the handle toward the top of the refrigerator door. (Fig. 1) 3. Open the refrigerator door and install the screws in to the top of the refrigerator door through the flat end of the handle Do not over-tighten screws. (Fig. 2) 4. If re-installing handles after reversing the door swing, remove screw hole plug from the parts-included bag and place it in the handle-mounting screw hole on the face of the refrigerator door. 5. The name badge can be removed by using a putty knife or flat head screwdriver to pry the badge off the door face, being careful not to damage the finish. Any residue left on the face of the door from the badge should be removed by using Goo Gone© or WD-40©. Be sure to follow the manufacturer's instructions when using these products. Do not use any abrasives or scouring pads to remove the residue. An extra logo badge is provided in the partsincluded bag with your refrigerator. That badge can be used to cover the handle mounting screw hole on the face of the freezer door. PAGE 8 • SET UP & USE

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
DOOR HANDLE INSTALLATION
For refrigerators with a mounting screw installed
on the face of both doors:
Remove both handles from inside freezer
compartment and screws from parts-included
bag.
FREEZER DOOR HANDLE
1. Place the tapered end of the handle over the
mounting screw on the freezer door and gently
slide handle in the direction of the flat end of
the handle. (Fig. 1)
2. Once the handle is fully seated around the
mounting screw, slowly rotate the flat end of
the handle toward the bottom of the freezer
door.
3. Open the freezer door and install the screws
into the underside of the freezer door through
the flat end of the handle. Do not use power
tools to install screws. Do not over-tighten the
screws.
REFRIGERATOR DOOR HANDLE
1. Place the tapered end of the handle over the
mounting screw on the refrigerator door and
gently slide handle in the direction of the flat
end of the handle. (Fig. 1)
2. Once the handle is fully seated around the
mounting screw, slowly rotate the flat end of
the handle toward the top of the refrigerator
door. (Fig. 1)
3. Open the refrigerator door and install
the screws in to the top of the refrigerator
door through the flat end of the handle
Do not over-tighten screws. (Fig. 2)
4. If re-installing handles after reversing the
door swing, remove screw hole plug from
the parts-included bag and place it in the
handle-mounting screw hole on the face of the
refrigerator door.
5. The name badge can be removed by using a
putty knife or flat head screwdriver to pry the
badge off the door face, being careful not to
damage the finish. Any residue left on the face
of the door from the badge should be removed
by using Goo Gone
©
or WD-40
©
. Be sure to
follow the manufacturer’s instructions when
using these products.
Do not use any abrasives or scouring pads to
remove the residue.
An extra logo badge is provided in the parts-
included bag with your refrigerator. That badge
can be used to cover the handle mounting screw
hole on the face of the freezer door.
DOOR HANDLE INSTALLATION
PAGE 8 • SET UP & USE
ENGLISH
Fig. 1
Fig. 2