HP 2000fc HP StorageWorks 2012fc Modular Smart Array user guide (481597-001, M - Page 50

Setting Management Port IP Addresses Using the CLI, Management Port IP Address, IP Subnet Mask

Get HP 2000fc PDF manuals and user guides View all HP 2000fc manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Setting Management Port IP Addresses Using the CLI Note - If you used DHCP to set the IP addresses, you do not have to set them using the CLI as described in this section. Ethernet Management ports on controller module A and controller module B are configured with the following default values: ■ Management Port IP Address: 10.0.0.2 (controller A), 10.0.0.3 (controller B) ■ IP Subnet Mask: 255.255.255.0 ■ Gateway IP Address: 10.0.0.1 If the default IP addresses are not compatible with your network, you must set an IP address for each management port using the command-line interface (CLI) embedded in each controller module. The CLI enables you to access the system using RS-232 communication and terminal emulation software. Use the CLI commands described in the steps below to set the IP address for the Ethernet management port on each controller module. Once new IP addresses are set, you can change them as needed using SMU. Note - Changing IP settings can cause management hosts to lose access to the storage system. 1. From your network administrator obtain an IP address, subnet mask, and gateway address for controller A and controller B. 2. Use the provided micro-DB9 serial cable to connect controller A to a serial port on a host computer. 50 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
50
HP StorageWorks 2012fc Modular Smart Array user guide
•
March 2008
Setting Management Port IP Addresses Using the CLI
Note –
If you used DHCP to set the IP addresses, you do not have to set them using
the CLI as described in this section.
Ethernet Management ports on controller module A and controller module B are
configured with the following default values:
■
Management Port IP Address:
10.0.0.2 (controller A), 10.0.0.3 (controller B)
■
IP Subnet Mask:
255.255.255.0
■
Gateway IP Address:
10.0.0.1
If the default IP addresses are not compatible with your network, you must set an IP
address for each management port using the command-line interface (CLI)
embedded in each controller module. The CLI enables you to access the system
using RS-232 communication and terminal emulation software.
Use the CLI commands described in the steps below to set the IP address for the
Ethernet management port on each controller module.
Once new IP addresses are set, you can change them as needed using SMU.
Note –
Changing IP settings can cause management hosts to lose access to the
storage system.
1.
From your network administrator obtain an IP address, subnet mask, and gateway
address for controller A and controller B.
2.
Use the provided micro-DB9 serial cable to connect controller A to a serial port on
a host computer.