HP 2000fc HP StorageWorks 2012fc Modular Smart Array user guide (481597-001, M - Page 52

specifies the controller whose network parameters you are setting

Get HP 2000fc PDF manuals and user guides View all HP 2000fc manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

4. In the terminal emulator, connect to controller A. 5. Press Enter to display the CLI prompt (#). 6. At the prompt, type the following command to set the values you obtained in Step 1 for each Ethernet management port, first for controller A and then for controller B: set network-parameters ip address netmask netmask gateway gateway controller a|b where: ■ address is the IP address of the controller ■ netmask is the subnet mask ■ gateway is the IP address of the subnet router ■ a|b specifies the controller whose network parameters you are setting For example: # set network-parameters ip 192.168.0.10 netmask 255.255.255.0 gateway 192.168.0.1 controller a # set network-parameters ip 192.168.0.11 netmask 255.255.255.0 gateway 192.168.0.1 controller b 7. Type the following command to verify the new IP addresses: show network-parameters Network parameters, including the IP address, subnet mask, and gateway address are displayed for each controller. 8. Disconnect from the CLI and exit the emulator. 52 HP StorageWorks 2012fc Modular Smart Array user guide • March 2008

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
52
HP StorageWorks 2012fc Modular Smart Array user guide
•
March 2008
4.
In the terminal emulator, connect to controller A.
5.
Press Enter to display the CLI prompt (#).
6.
At the prompt, type the following command to set the values you obtained in Step 1
for each Ethernet management port, first for controller A and then for controller B:
where:
■
address
is the IP address of the controller
■
netmask
is the subnet mask
■
gateway
is the IP address of the subnet router
■
a|b
specifies the controller whose network parameters you are setting
For example:
7.
Type the following command to verify the new IP addresses:
Network parameters, including the IP address, subnet mask, and gateway address
are displayed for each controller.
8.
Disconnect from the CLI and exit the emulator.
set network-parameters ip
address
netmask
netmask
gateway
gateway
controller a|b
#
set network-parameters ip 192.168.0.10 netmask 255.255.255.0
gateway 192.168.0.1 controller a
#
set network-parameters ip 192.168.0.11 netmask 255.255.255.0
gateway 192.168.0.1 controller b
show network-parameters